- 您現在的位置：買賣IC網 > PDF目錄68460 > W78M32VP110BM (WHITE ELECTRONIC DESIGNS CORP) 8M X 32 FLASH 3.3V PROM, 110 ns, PBGA159 PDF資料下載
參數資料
| 型號： | W78M32VP110BM |
| 廠商： | WHITE ELECTRONIC DESIGNS CORP |
| 元件分類： | PROM |
| 英文描述： | 8M X 32 FLASH 3.3V PROM, 110 ns, PBGA159 |
| 封裝： | 13 X 22 MM, 1.27 MM PITCH, PLASTIC, BGA-159 |
| 文件頁數： | 34/51頁 |
| 文件大小： | 1637K |
| 代理商： | W78M32VP110BM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
4
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W78M32VP-XBX
January 2010
Rev. 12
White Electronic Designs Corp. reserves the right to change products or specications without notice.
AUTOSELECT
The Autoselect mode provides manufacturer ID, Device
identication, and sector protection information, through
identier codes output from the internal register (separate
from the memory array) on DQ7-DQ0. This mode is primarily
intended for programming equipment to automatically
match a device to be programmed with its corresponding
programming algorithm (see Table 4). The Autoselect codes
can also be accessed in-system.
There are two methods to access autoselect codes. One
uses the autoselect command, the other applies VID on
address pin A9.
When using programming equipment, the autoselect mode
requires VID (11.5 V to 12.5 V) on address pin A9. Address
pins must be as shown in Table 3.
To access Autoselect mode without using high
voltage on A9, the host system must issue the
Autoselect command.
The Autoselect command sequence may be written
to an address within a sector that is either in the read
or erase-suspend-read mode.
The Autoselect command may not be written while
the device is actively programming or erasing.
The system must write the reset command to return
to the read mode (or erase-suspend-read mode if the
sector was previously in Erase Suspend).
It is recommended that A9 apply VID after power-
up sequence is completed. In addition, it is
recommended that A9 apply from VID to VIH/VIL
before power-down the VCC/VIO.
See Table 39 for command sequence details.
When verifying sector protection, the sector address
must appear on the appropriate highest order
address bits (see Table 5 to Table 6). The remaining
address bits are don't care. When all necessary
bits have been set as required, the programming
equipment may then read the corresponding
identier code on DQ15-DQ0. The Autoselect
codes can also be accessed in-system through the
command register.
PROGRAM/ERASE OPERATIONS
These devices are capable of several modes of programming
and or erase operations which are described in detail in the
following sections.
During a write operation, the system must drive CE#
and WE# to VIL and OE# to VIH when providing address,
command, and data. Addresses are latched on the last
falling edge of WE# or CE#, while data is latched on the
1st rising edge of WE# or CE#.
The Unlock Bypass feature allows the host system to send
program commands to the Flash device without rst writing
unlock cycles within the command sequence. See Unlock
Bypass section for details on the Unlock Bypass function.
Note the following:
When the Embedded Program algorithm is complete,
the device returns to the read mode.
The system can determine the status of the program
operation by reading the DQ status bits. Refer to
the Write Operation Status for information on these
status bits.
An “0” cannot be programmed back to a “1.” A
succeeding read shows that the data is still “0.”
Only erase operations can convert a “0” to a “1.”
Any commands written to the device during the
Embedded Program/Erase are ignored except the
Suspend commands.
Secured Silicon Sector, Autoselect, and CFI
functions are unavailable when a program operation
is in progress.
A hardware reset and/or power removal immediately
terminates the Program/Erase operation and the
Program/Erase command sequence should be
reinitiated once the device has returned to the read
mode to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries for single word programming
operation. See Write Buffer Programming when
using the write buffer.
Programming to the same word address multiple
times without intervening erases is permitted.
SINGLE WORD PROGRAMMING
Single word programming mode is one method of
programming the Flash. In this mode, four Flash command
write cycles are used to program an individual Flash
address. The data for this programming operation could
be 8 or 16-bits wide.
While the single word programming method is supported
相關PDF資料 |
PDF描述 |
|---|---|
| W78M64V-120SBC | 8M X 64 FLASH 3.3V PROM MODULE, 120 ns, PBGA159 |
| W78M64V-100SBM | 8M X 64 FLASH 3.3V PROM MODULE, 100 ns, PBGA159 |
| W7NCF04GH11CS4DG | 256M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF04GH11IS2BG | 256M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF04GH11IS7JG | 256M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78M32VP-110BM | 制造商:White Electronic Designs 功能描述:Flash Module Parallel 256Mbit |
| W78M32V-XBX | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:8Mx32 Flash 3.3V Page Mode Simultaneous Read/Write Operation Multi-Chip Package |
| W78M64VP110SBM | 制造商:Microsemi Corporation 功能描述:8MX64 FLASH 3.3V PAGE MODE - Bulk |
| W78M64V-XSBX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash MCP |
| W78NCSX-23 | 功能描述:低信號繼電器 - PCB 4PDT 3A 24VDC IND RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
發布緊急采購，3分鐘左右您將得到回復。