- 您現在的位置：買賣IC網 > PDF目錄371190 > X1243S8 (INTERSIL CORP) Real Time Clock/Calendar/Alarm with EEPROM PDF資料下載
參數資料
| 型號： | X1243S8 |
| 廠商： | INTERSIL CORP |
| 元件分類： | XO, clock |
| 英文描述： | Real Time Clock/Calendar/Alarm with EEPROM |
| 中文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | PLASTIC, SOIC-8 |
| 文件頁數： | 5/18頁 |
| 文件大?。?/td> | 90K |
| 代理商： | X1243S8 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
X1243
5
value to a specific day of the week is arbitrary and may
be decided by the system software designer. The Clock
Default values define 0=Sunday.
Clock/Calendar Registers (YR, MO, DT, HR, MN, SC)
These registers depict BCD representations of the time.
As such, SC (Seconds) and MN (Minutes) range from
00 to 59, HR (Hour) is 1 to 12 with an AM or PM indica-
tor (H21 bit) or 0 to 23 (with T24=1), DT (Date) is 1 to
31, MO (Month) is 1 to 12, YR (year) is 0 to 99.
24 Hour Time
If the T24 bit of the HR register is 1, the RTC will use a
24-hour format. If the T24 bit is 0, the RTC will use 12-
hour format and bit H21 will function as an AM/PM indi-
cator with a ‘1’ representing PM. The clock defaults to
Standard Time with H21=0.
Leap Years
Leap years add the day February 29 and are defined as
those years that are divisible by 4. Years divisible by
100 are not leap years, unless they are also divisible by
400. This means that the year 2000 is a leap year, the
year 2100 is not. The X1243 does not correct for the
leap year in the year 2100.
STATUS REGISTER (SR)
The Status Register is located in the RTC area at
address 003FH. This is a volatile register only and is
used to control the WEL and RWEL write enable
latches, read an optional Low Voltage Sense bit, and
read the two alarm bits. This register is logically seper-
ated from both the array and the Clock/Control Regis-
ters (CCR).
Table 2. Status Register (SR)
BAT: Battery Supply—Volatile
This bit set to “1” indicates that the device is operating
from V
BACK
, not V
CC
. It is a read only bit and is set/
reset by hardware.
AL1, AL0: Alarm bits—Volatile
These bits announce if either alarm 1 or alarm 2 match
the real time clock. If there is a match, the respective bit
is set to ‘1’. The falling edge of the last data bit in a SR
Read operation resets the flags. Note: Only the AL bits
that are set when an SR read starts will be reset. An
alarm bit that is set by an alarm occuring during an SR
read operation will remain set after the read operation
is complete.
RWEL: Register Write Enable Latch—Volatile
This bit is a volatile latch that powers up in the LOW
(disabled) state. The RWEL bit must be set to “1” prior
to any writes to the Clock/Control Registers. Writes to
RWEL bit do not cause a nonvolatile write cycle, so the
device is ready for the next operation immediately after
the stop condition. A write to the CCR requires both the
RWEL and WEL bits to be set in a specific sequence.
WEL: Write Enable Latch—Volatile
The WEL bit controls the access to the CCR and mem-
ory array during a write operation. This bit is a volatile
latch that powers up in the LOW (disabled) state. While
the WEL bit is LOW, writes to the CCR or any array
address will be ignored (no acknowledge will be issued
after the Data Byte). The WEL bit is set by writing a “1”
to the WEL bit and zeroes to the other bits of the Status
Register. Once set, WEL remains set until either reset
to 0 (by writing a “0” to the WEL bit and zeroes to the
other bits of the Status Register) or until the part pow-
ers up again. Writes to WEL bit do not cause a non-vol-
atile write cycle, so the device is ready for the next
operation immediately after the stop condition.
RTCF: Real Time Clock Fail Bit—Volatile
This bit is set to a ‘1’ after a total power failure. This is a
read only bit that is set by hardware when the device
powers up after having lost all power to the device. The
bit is set regardless of whether V
first. The loss of one or the other supplies does not
result in setting the RTCF bit. The first valid write to the
RTC (writing one byte is sufficient) resets the RTCF bit
to ‘0’.
CC
or V
BACK
is applied
Unused Bits:
These devices do not use bits 3 or 4, but must have a
zero in these bit positions. The Data Byte output during
a SR read will contain zeros in these bit locations.
Addr
7
6
5
4
3
2
1
0
003Fh
BAT
AL1
AL0
0
0
RWEL
WEL
RTCF
Default
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| X1243S8I | Real Time Clock/Calendar/Alarm with EEPROM |
| X1243V8 | Real Time Clock/Calendar/Alarm with EEPROM |
| X125-55FA | 30V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; Similar to the IRF3703 with Lead-Free Packaging. |
| X125-56FA | 30V Single N-Channel HEXFET Power MOSFET in a TO-262 package; Similar to IRF3708L with Lead Free Packaging |
| X125-57FA | BEACON STATIC 12VDC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1243S8I | 制造商:Intersil Corporation 功能描述: 制造商:XICOR 功能描述: |
| X1243V8 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Real Time Clock/Calendar/Alarm with EEPROM |
| X-1244 | 制造商:Pulse 功能描述:TRANSFORMERS - Rail/Tube |
| X124K | 制造商:IQD Frequency Products 功能描述:CRYSTAL OSCILLATOR 8.192000MHZ |
| X124LE0 | 制造商:SENSORTECHNICS 制造商全稱:Sensortechnics GmbH 功能描述:8 mm switching soleniod valves |
發布緊急采購，3分鐘左右您將得到回復。