- 您現在的位置：買賣IC網 > PDF目錄9336 > X1286V14IT1 (Intersil)IC RTC/CAL/CPU SUP EE 14-TSSOP PDF資料下載
參數資料
| 型號： | X1286V14IT1 |
| 廠商： | Intersil |
| 文件頁數： | 5/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，監控器，監視計時器 |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
13
FN8101.1
April 14, 2006
INTERRUPT CONTROL AND FREQUENCY
OUTPUT REGISTER (INT)
Interrupt Control and Status Bits (IM, AL1E, AL0E)
There are two Interrupt Control bits, Alarm 1 Interrupt
Enable (AL1E) and Alarm 0 Interrupt Enable (AL0E) to
specifically enable or disable the alarm interrupt signal
output (IRQ). The interrupts are enabled when either
AL1E and AL0E are set to ‘1’, respectively.
Two volatile bits (AL1 and AL0), associated with the
two alarms respectively, indicate if an alarm has hap-
pened. These bits are set on an alarm condition
regardless of whether the IRQ interrupt is enabled.
The AL1 and AL0 bits in the status register are reset
by the falling edge of the eighth clock of a read of the
register containing the bits.
Pulse Interrupt Mode
The pulsed interrupt mode allows for repetitive or
recurring alarm functionality. Hence an repetitive or
recurring alarm can be set for every nth second, or nth
minute, or nth hour, or nth date, or for the same day of
the week. The pulsed interrupt mode can be consid-
ered a repetitive interrupt mode, with the repetition
rate set by the time setting fo the alarm.
The Pulse Interrupt Mode is enabled when the IM bit is
set.
The Alarm IRQ output will output a single pulse of
short duration (approximately 10-40ms) once the
alarm condition is met. If the interrupt mode bit (IM bit)
is set, then this pulse will be periodic.
Programmable Frequency Output Bits—FO1, FO0
These are two output control bits. They select one of
three divisions of the internal oscillator, that is applied
to the PHZ output pin. Table 5 shows the selection bits
for this output. When using the PHZ output function,
the Alarm IRQ output function is disabled.
Table 5. Programmable Frequency Output Bits
ON-CHIP OSCILLATOR COMPENSATION
Digital Trimming Register (DTR) — DTR2, DTR1
and DTR0 (Non-Volatile)
The digital trimming Bits DTR2, DTR1 and DTR0
adjust the number of counts per second and average
the ppm error to achieve better accuracy.
DTR2 is a sign bit. DTR2=0 means frequency
compensation is > 0. DTR2=1 means frequency
compensation is < 0.
DTR1 and DTR0 are scale bits. DTR1 gives 10 ppm
adjustment and DTR0 gives 20 ppm adjustment.
A range from -30ppm to +30ppm can be represented
by using three bits above.
Table 6. Digital Trimming Registers
Analog Trimming Register (ATR) (Non-volatile)
Six analog trimming Bits from ATR5 to ATR0 are pro-
vided to adjust the on-chip loading capacitance range.
The on-chip load capacitance ranges from 3.25pF to
18.75pF. Each bit has a different weight for capacitance
adjustment. Using a Citizen CFS-206 crystal with differ-
ent ATR bit combinations provides an estimated ppm
range from +116ppm to -37ppm to the nominal fre-
quency compensation. The combination of digital and
analog trimming can give up to +146ppm adjustment.
The on-chip capacitance can be calculated as follows:
CATR = [(ATR value, decimal) x 0.25pF] + 11.0pF
Note that the ATR values are in two’s complement,
with ATR(000000) = 11.0pF, so the entire range runs
from 3.25pF to 18.75pF in 0.25pF steps.
The values calculated above are typical, and total load
capacitance seen by the crystal will include approxi-
mately 2pF of package and board capacitance in addi-
tion to the ATR value.
See Application section and Intersil’s application Note
AN154 for more information.
IM Bit
Interrupt/Alarm Frequency
0
Single Time Event Set By Alarm
1
Repetitive/Recurring Time Event Set By Alarm
FO1
FO0
Output Frequency
(average of 100 samples)
00
Alarm IRQ output
0
1
32.768kHz
1
0
100Hz
11
1Hz
DTR Register
Estimated frequency
PPM
DTR2
DTR1
DTR0
00
0
01
0
+10
00
1
+20
01
1
+30
10
0
11
0
-10
10
1
-20
11
1
-30
X1286
相關PDF資料 |
PDF描述 |
|---|---|
| X1286V14I | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| MS27656E21B35SD | CONN RCPT 79POS WALL MNT W/SCKT |
| MS27656E21B35SC | CONN RCPT 79POS WALL MNT W/SCKT |
| VE-BNT-MY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-BNT-MY-F3 | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1286V14IZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Intersil Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1286V14T1 | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1286V14Z | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Intersil Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1288 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:2-Wire RTC Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1288S16 | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。