- 您現在的位置：買賣IC網 > PDF目錄9336 > X1286V14IT1 (Intersil)IC RTC/CAL/CPU SUP EE 14-TSSOP PDF資料下載
參數資料
| 型號： | X1286V14IT1 |
| 廠商： | Intersil |
| 文件頁數： | 6/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，監控器，監視計時器 |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
14
FN8101.1
April 14, 2006
WRITING TO THE CLOCK/CONTROL REGISTERS
Changing any of the nonvolatile bits of the clock/
control register requires the following steps:
– Write a 02h to the Status Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation pre-
ceeded by a start and ended with a stop).
– Write a 06h to the Status Register to set both the
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation preceeded by a start
and ended with a stop).
– Write one to 8 bytes to the Clock/Control Registers
with the desired clock, alarm, or control data. This
sequence starts with a start bit, requires a slave byte
of “11011110” and an address within the CCR and is
terminated by a stop bit. A write to the CCR changes
EEPROM values so these initiate a nonvolatile write
cycle and will take up to 10ms to complete. Writes to
undefined areas have no effect. The RWEL bit is
reset by the completion of a nonvolatile write cycle,
so the sequence must be repeated to again initiate
another change to the CCR contents. If the
sequence is not completed for any reason (by send-
ing an incorrect number of bits or sending a start
instead of a stop, for example) the RWEL bit is not
reset and the device remains in an active mode.
– Writing all zeros to the status register resets both the
WEL and RWEL bits.
– A read operation occurring between any of the previ-
ous operations will not interrupt the register write
operation.
SERIAL COMMUNICATION
Interface Conventions
The device supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter, and the receiving device
as the receiver. The device controlling the transfer is
called the master and the device being controlled is
called the slave. The master always initiates data
transfers, and provides the clock for both transmit and
receive operations. Therefore, the devices in this fam-
ily operate as slaves in all applications.
Clock and Data
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. See
.
Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL
is HIGH. The device continuously monitors the SDA
and SCL lines for the start condition and will not
respond to any command until this condition has been
met. See Figure 5.
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
when SCL is HIGH. The stop condition is also used to
place the device into the Standby power mode after a
read sequence. A stop condition can only be issued
after the transmitting device has released the bus. See
.
Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfer. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data. Refer to Figure 6.
The device will respond with an acknowledge after
recognition of a start condition and if the correct
Device Identifier and Select bits are contained in the
Slave Address Byte. If a write operation is selected,
the device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for:
– The Slave Address Byte when the Device Identifier
and/or Select bits are incorrect
– All Data Bytes of a write when the WEL in the Write
Protect Register is LOW
– The 2nd Data Byte of a Status Register Write Opera-
tion (only 1 data byte is allowed)
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
detected. The master must then issue a stop condition
to return the device to Standby mode and place the
device into a known state.
X1286
相關PDF資料 |
PDF描述 |
|---|---|
| X1286V14I | IC RTC/CAL/CPU SUP EE 14-TSSOP |
| MS27656E21B35SD | CONN RCPT 79POS WALL MNT W/SCKT |
| MS27656E21B35SC | CONN RCPT 79POS WALL MNT W/SCKT |
| VE-BNT-MY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-BNT-MY-F3 | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1286V14IZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Intersil Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1286V14T1 | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1286V14Z | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Intersil Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1288 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:2-Wire RTC Real Time Clock/Calendar/CPU Supervisor with EEPROM |
| X1288S16 | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。