參數資料
型號： X3100
英文描述： Reed Relay; Contacts:SPST; Switching Current Max:0.5A; Switching Voltage Max:200V; Contact Carry Current:1A; Coil Voltage DC Max:5V; Relay Terminals:DIP-14; Relay Mounting:PC Board; Contact Carrying Power:10W
中文描述： 3或4芯鋰離子電池保護和監控器IC
文件頁數： 19/40頁
文件大?。?/td> 249K
代理商： X3100
X3100/X3101 – Preliminary Information
Characteristics subject to change without notice.
19 of 40
REV 1.1.8 12/10/02
www.xicor.com
Figure 8. Over-Current Protection Mode—Event Diagram
P+
VCS
2
UVP/OCP
T
OCR
V
SS
Over-Current Protection Mode
T
OC
Voc
Normal Operation Mode
P+ = (RLOAD+RSENSE) x ILMON
V
OC
Normal Operation Mode
Event
0
1
3
4
2
V
SS
V
CC
B+
Table 24. Over-Current Protection Mode—Event Diagram Description
Event
Event Description
[0,1)
—Discharge FET is ON (OCP=Vss). Battery cells are permitted to discharge.
—VCS
21
(VCS
2
–VCS
1
) is less than the over-current threshold voltage (V
OC
).
—The device is in normal operation mode (i.e. not in a protection mode).
[1]
—Excessive current flows through the battery terminals P+, dropping the voltage. (See Figure 8.).
—The positive battery terminal voltage (P+) falls, and VCS
21
exceeds V
OC
.
—The internal over-current detection delay timer begins counting down.
—The device is still in Normal Operation Mode
The internal Over-current detection delay timer continues counting for T
OC
seconds.
(1,2)
[2]
—The internal over-current detection delay timer times out, AND VCS
21
is still above V
OC.
—The internal over-current sense circuitry switches the discharge FET OFF (UVP/OCP=Vcc).
—The device now begins a load monitor state by passing a small test current (I
LMON
=7.5μA) out of pin
OVP/LMON. This senses if an over-current condition (i.e. if the load resistance < 150k
) still exists
across P+/P-.
—The device has now entered over-current protection mode.
—It is possible to change the status of UVPC and OVPC in the control register, although the status of pins
UVP/OCP and OVP/LMON will not change until the device has returned from over-current protection
mode.
(2,3)
—The X3100/X3101 now continuously monitors the load resistance to detect whether or not an over-
current condition is still present across the battery terminals P+/P-.
相關PDF資料
PDF描述
X3100Q WAFER(ARM)
X3100V QFN,GREEN,IND TEMP,T&R(ARM)
X3101PT-V 3 or 4 Cell Li-Ion Battery Protection and Monitor IC
X3100 Reed Relay; Contacts:SPST; Switching Current Max:0.5A; Switching Voltage Max:200V; Contact Carry Current:1A; Coil Voltage DC Max:5V; Relay Terminals:DIP-14; Relay Mounting:PC Board; Contact Carrying Power:10W
X3100V28 Reed Relay; Contacts:SPST; Contact Carry Current:1A; Coil Voltage DC Max:5V; Relay Terminals:Thru Hole; Switching Current Max:0.5A; Switching Voltage Max:200V; Contact Carrying Power:10W; Leaded Process Compatible:Yes RoHS Compliant: Yes
相關代理商/技術參數
參數描述
X3100_08 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3 or 4 Cell Li-ion Battery Protection and Monitor IC
X310014 制造商:MERSEN / FERRAZ SHAWMUT 功能描述:MICROCONTACT FOR PROTISTOR 制造商:MERSEN / FERRAZ SHAWMUT 功能描述:MICROCONTACT, FOR PROTISTOR 制造商:MERSEN / FERRAZ SHAWMUT 功能描述:MICROCONTACT, FOR PROTISTOR; Contact Configuration:-; Microswitch Type:-; Actuator Style:Top; Switch Operation:-; Contact Current AC:3A; Contact Current AC Max:16A; Contact Current DC Max:10A; Contact Voltage AC Max:1kV; Contact
X3100PT-V 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:3 or 4 Cell Li-Ion Battery Protection and Monitor IC
X3100Q 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
X3100V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*