參數資料
型號： X3100
英文描述： Reed Relay; Contacts:SPST; Switching Current Max:0.5A; Switching Voltage Max:200V; Contact Carry Current:1A; Coil Voltage DC Max:5V; Relay Terminals:DIP-14; Relay Mounting:PC Board; Contact Carrying Power:10W
中文描述： 3或4芯鋰離子電池保護和監控器IC
文件頁數： 3/40頁
文件大?。?/td> 249K
代理商： X3100
X3100/X3101 – Preliminary Information
Characteristics subject to change without notice.
3 of 40
REV 1.1.8 12/10/02
www.xicor.com
Cell Voltage Balancing Control (CB1-CB4):
These outputs are used to switch external FETs in order
to perform cell voltage balancing control. This function
can be used to adjust individual cell voltages (e.g.
during cell charging). CB1–CB4 can be driven high
(Vcc) or low (Vss) to switch external FETs ON/OFF. When
using the X3101, the CB4 pin can be left unconnected,
or the FET control can be used for other purposes.
Current Sense Inputs (VCS1–VCS2):
A sense resistor (R
SENSE
and VCS2 (Figure 1). R
order of 20m
to 100m
flowing through the battery terminals, and protect
against over-current conditions. The voltage at each end
of R
SENSE
can also be monitored at pin AO.
) is connected between VCS1
has a resistance in the
, and is used to monitor current
SENSE
Over-charge Voltage detect Time control (OVT):
This pin is used to control the delay time (T
associated with the detection of an over-charge
condition (see section “Over-charge Protection” on page
13).
OV
)
Over-discharge detect/release time control (UVT):
This pin is used to control the delay times associated
with the detection (T
UV
) and release (T
discharge (under-voltage) condition (see section “Over-
discharge Protection” on page 15).
UVR
) of an over-
Over-current detect/release time control (OCT):
This pin is used to control the delay times associated
with the detection (T
OC
) and release (T
current condition (see section “Over-Current Protection”
on page 18).
OCR
) of an over-
Analog Output (AO):
The analog output pin is used to externally monitor
various battery parameter voltages. The voltages which
can be monitored at AO (see section “Analog
Multiplexer Selection” on page 20) are:
– Individual cell voltages
– Voltage across the current sense resistor (R
This voltage is amplified with a gain set by the user in
the control register (see section “Current Monitor
Function” on page 20.)
SENSE
)
.
The analog select pins pins AS0–AS2 select the desired
voltage to be monitored on the AO pin.
Analog Output Select (AS0–AS2):
These pins select which voltage is to be multiplexed to
the output AO (see section “Sleep Control (SLP)” on
page 10 and section “Current Monitor Function” on
page 20)
Serial Input (SI):
SI is the serial data input pin. All opcodes, byte
addresses, and data to be written to the device are input
on this pin.
Serial Output (SO):
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked out
by the falling edge of the serial clock. While CS is HIGH,
SO will be in a High Impedance state.
Note:
(SI/SO). In this case, all serial data communication with
the X3100 or X3101 is undertaken over one I/O line.
This is permitted ONLY if no simultaneous read/write
operations occur.
SI and SO may be tied together to form one line
Serial Clock (SCK):
The Serial Clock controls the serial bus timing for data
input and output. Opcodes, addresses, or data present
on the SI pin are latched on the rising edge of the clock
input, while data on the SO pin change after the falling
edge of the clock input.
Chip Select (CS):
When CS is HIGH, the device is deselected and the SO
output pin is at high impedance. CS LOW enables the
SPI serial bus.
Over-charge Voltage Protection/Load Monitor
(OVP/LMON):
This one pin performs two functions depending upon
the present mode of operation of the X3100 or X3101.
—Over-charge Voltage Protection (OVP)
This pin controls the switching of the battery pack charge
FET. This power FET is a P-channel device. As such,
cell charge is possible when OVP/LMON=V
charge is prohibited when OVP/LMON=V
configuration the X3100 and X3101 turn off the charge
voltage when the cells reach the over-charge limit. This
prevents damage to the battery cells due to the
application of charging voltage for an extended period of
time (see section “Over-charge Protection” on page 13).
SS
CC
, and cell
. In this
相關PDF資料
PDF描述
X3100Q WAFER(ARM)
X3100V QFN,GREEN,IND TEMP,T&R(ARM)
X3101PT-V 3 or 4 Cell Li-Ion Battery Protection and Monitor IC
X3100 Reed Relay; Contacts:SPST; Switching Current Max:0.5A; Switching Voltage Max:200V; Contact Carry Current:1A; Coil Voltage DC Max:5V; Relay Terminals:DIP-14; Relay Mounting:PC Board; Contact Carrying Power:10W
X3100V28 Reed Relay; Contacts:SPST; Contact Carry Current:1A; Coil Voltage DC Max:5V; Relay Terminals:Thru Hole; Switching Current Max:0.5A; Switching Voltage Max:200V; Contact Carrying Power:10W; Leaded Process Compatible:Yes RoHS Compliant: Yes
相關代理商/技術參數
參數描述
X3100_08 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3 or 4 Cell Li-ion Battery Protection and Monitor IC
X310014 制造商:MERSEN / FERRAZ SHAWMUT 功能描述:MICROCONTACT FOR PROTISTOR 制造商:MERSEN / FERRAZ SHAWMUT 功能描述:MICROCONTACT, FOR PROTISTOR 制造商:MERSEN / FERRAZ SHAWMUT 功能描述:MICROCONTACT, FOR PROTISTOR; Contact Configuration:-; Microswitch Type:-; Actuator Style:Top; Switch Operation:-; Contact Current AC:3A; Contact Current AC Max:16A; Contact Current DC Max:10A; Contact Voltage AC Max:1kV; Contact
X3100PT-V 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:3 or 4 Cell Li-Ion Battery Protection and Monitor IC
X3100Q 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
X3100V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*