- 您現在的位置：買賣IC網 > PDF目錄4284 > XC2S100E-6FT256C (Xilinx Inc)IC FPGA 1.8V 600 CLB'S 256-FBGA PDF資料下載
參數資料
| 型號： | XC2S100E-6FT256C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 30/108頁 |
| 文件大小： | 0K |
| 描述： | IC FPGA 1.8V 600 CLB'S 256-FBGA |
| 產品變化通告： | FPGA Family Discontinuation 18/Apr/2011 |
| 標準包裝： | 90 |
| 系列： | Spartan®-IIE |
| LAB/CLB數： | 600 |
| 邏輯元件/單元數： | 2700 |
| RAM 位總計： | 40960 |
| 輸入/輸出數： | 182 |
| 門數： | 100000 |
| 電源電壓： | 1.71 V ~ 1.89 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 256-LBGA |
| 供應商設備封裝： | 256-FTBGA |
| 其它名稱： | 122-1208 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
28
DS077-2 (v3.0) August 9, 2013
Product Specification
Spartan-IIE FPGA Family: Functional Description
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
If CCLK is slower than FCCNH, the FPGA will never assert
BUSY. In this case, the above handshake is unnecessary,
and data can simply be entered into the FPGA every CCLK
cycle.
A configuration packet does not have to be written in one
continuous stretch, rather it can be split into many write
sequences. Each sequence would involve assertion of CS.
In applications where multiple clock cycles may be required
to access the configuration data before each byte can be
loaded into the Slave Parallel interface, a new byte of data
may not be ready for each consecutive CCLK edge. In such
a case the CS signal may be deasserted until the next byte
is valid on D0-D7. While CS is High, the Slave Parallel inter-
face does not expect any data and ignores all CCLK transi-
tions. However, to avoid aborting configuration, WRITE
must continue to be asserted while CS is asserted during
CCLK transitions.
Abort
To abort configuration during a write sequence, deassert
WRITE while holding CS Low. The abort operation is initi-
ated at the rising edge of CCLK. The device will remain
BUSY until the aborted operation is complete. After aborting
configuration, data is assumed to be unaligned to word
boundaries and the FPGA requires a new synchronization
word prior to accepting any new packets.
Boundary-Scan Configuration Mode
In the boundary-scan mode, no nondedicated pins are
required, configuration being done entirely through the
IEEE 1149.1 Test Access Port (TAP).
Configuration through the TAP uses the special CFG_IN
instruction. This instruction allows data input on TDI to be
converted into data packets for the internal configuration
bus.
The following steps are required to configure the FPGA
through the boundary-scan port.
1.
Load the CFG_IN instruction into the boundary-scan
instruction register (IR)
2.
Enter the Shift-DR (SDR) state
3.
Shift a standard configuration bitstream into TDI
4.
Return to Run-Test-Idle (RTI)
5.
Load the JSTART instruction into IR
6.
Enter the SDR state
7.
Clock TCK (if selected) through the startup sequence
(the length is programmable)
8.
Return to RTI
Configuration and readback via the TAP is always available.
The boundary-scan mode simply locks out the other modes.
The boundary-scan mode is selected by a <10x> on the
mode pins (M0, M1, M2). Note that the PROGRAM pin must
be pulled High prior to reconfiguration. A Low on the PRO-
GRAM pin resets the TAP controller and no boundary scan
operations can be performed. See Xilinx Application Note
XAPP188 for more information on boundary-scan configu-
ration.
Readback
The configuration data stored in the Spartan-IIE FPGA con-
figuration memory can be read back for verification. Along
with the configuration data it is possible to read back the
contents of all flip-flops/latches, LUT RAMs, and block
RAMs. This capability is used for real-time debugging.
For more detailed information see Xilinx Application Note
XAPP176, Configuration and Readback of the Spartan-II
and Spartan-IIE FPGA Families.
Figure 21: Loading Configuration Data for the Slave
Parallel Mode
Yes
No
FPGA
Driving BUSY
High?
After INIT
Goes High
Load One
Configuration
Byte on Next
CCLK Rising Edge
To CRC Check
DS001_19_032300
No
End of
Configuration
Data File?
Yes
User Drives
WRITE and CS
Low
User Drives
WRITE and CS
High
相關PDF資料 |
PDF描述 |
|---|---|
| ABB91DHFT-S578 | EDGECARD 182POS .050 SMD W/POSTS |
| 24FC64FT-I/ST | IC EEPROM 64KBIT 1MHZ 8TSSOP |
| 24FC64FT-I/MS | IC EEPROM 64KBIT 1MHZ 8MSOP |
| 24LC64FT-E/OT | IC SRL EEPROM 8KX8 2.5V SOT23-5 |
| XC3S700A-4FT256I | IC FPGA SPARTAN 3 256FTBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC2S100E6FT256I | 制造商:Xilinx 功能描述: |
| XC2S100E-6FT256I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA |
| XC2S100E-6FTG256C | 功能描述:IC SPARTAN-IIE FPGA 100K 256FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-IIE 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA（27x27） |
| XC2S100E-6FTG256I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA |
| XC2S100E-6PQ208C | 功能描述:IC FPGA 1.8V 600 CLB'S 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-IIE 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA（27x27） |
發布緊急采購，3分鐘左右您將得到回復。