- 您現在的位置：買賣IC網 > PDF目錄376453 > XR16C2852 (Exar Corporation) 3.3V AND 5V DUART WITH 128-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16C2852 |
| 廠商： | Exar Corporation |
| 英文描述： | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| 中文描述： | 3.3V和5V杜阿爾特128字節FIFO |
| 文件頁數： | 14/42頁 |
| 文件大?。?/td> | 574K |
| 代理商： | XR16C2852 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
á
3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2852
REV. 2.0.0
14
2.16 A
UTO
X
ON
/X
OFF
(S
OFTWARE
) F
LOW
C
ONTROL
When software flow control is enabled (See
Table 15), the 2852 compares one or two sequential
receive data characters with the programmed Xon or
Xoff-1,2 character value(s). If receive character(s)
(RX) match the programmed values, the 2852 will halt
transmission (TX) as soon as the current character
has completed transmission. When a match occurs,
the Xoff (if enabled via IER bit-5) flag will be set and
the interrupt output pin will be activated. Following a
suspension due to a match of the Xoff character, the
2852 will monitor the receive data stream for a match
to the Xon-1,2 character. If a match is found, the 2852
will resume operation and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit
flow control registers to a logic 0. Following reset the
user can write any Xon/Xoff value desired for soft-
ware flow control. Different conditions can be set to
detect Xon/Xoff characters (See Table 15) and sus-
pend/resume transmissions. When double 8-bit Xon/
Xoff characters are selected, the 2852 compares two
consecutive receive characters with two software flow
control 8-bit values (Xon1, Xon2, Xoff1, Xoff2) and
controls TX transmissions accordingly. Under the
above described flow control mechanisms, flow con-
trol characters are not placed (stacked) in the user
accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and
flow control needs to be executed, the 2852 automat-
F
IGURE
11. A
UTO
RTS
AND
CTS F
LOW
C
ONTROL
O
PERATION
The local UART (UARTA) starts data transfer by asserting RTSA# (1). RTSA# is normally connected to CTSB# (2) of
remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO
(4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and con-
tinues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA
monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows
(7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its trans-
mit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9),
UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until
next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB
with RTSB# and CTSA# controlling the data flow.
RTSA#
CTSB#
RXA
TXB
Transmitter
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Auto CTS
Monitor
RTSA#
TXB
RXA FIFO
CTSB#
Remote UART
UARTB
Local UART
UARTA
ON
OFF
ON
Suspend
Restart
RTS High
Threshold
Data Starts
ON
OFF
ON
Assert RTS# to Begin
Transmission
1
2
3
4
5
6
7
Receive
Data
RTS Low
Threshold
9
10
11
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Transmitter
Auto CTS
Monitor
RTSB#
CTSA#
RXB
TXA
INTA
(RXA FIFO
Interrupt)
RX FIFO
Trigger Level
RX FIFO
Trigger Level
8
12
RTSCTS1
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C2852CJ | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2852IJ | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C850CJ | UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control |
| XR16C850CM | UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control |
| XR16C850CP | UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2852_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS |
| XR16C2852CJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16C2852CJ-0A-EB | 功能描述:UART 接口集成電路 Supports C2852 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2852CJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2852CJTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。