- 您現在的位置：買賣IC網 > PDF目錄376453 > XR16C2852 (Exar Corporation) 3.3V AND 5V DUART WITH 128-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16C2852 |
| 廠商： | Exar Corporation |
| 英文描述： | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| 中文描述： | 3.3V和5V杜阿爾特128字節FIFO |
| 文件頁數： | 4/42頁 |
| 文件大?。?/td> | 574K |
| 代理商： | XR16C2852 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
á
3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2852
REV. 2.0.0
4
MFB#
19
O
Multi-Function Output ChannelB. This output pin can function as the OP2B#, BAUD-
OUTB#, or RXRDYB# pin. One of these output signal functions can be selected by
the user programmable bits 1-2 of the Alternate Function Register (AFR). These sig-
nal functions are described as follows:
1) OP2B# - When OP2B# (active low) is selected, the MF# pin is a logic 0 when MCR
bit-3 is set to a logic 1 (see MCR bit-3). MCR bit-3 defaults to a logic 1 condition after
a reset or power-up.
2) BAUDOUTB# - When BAUDOUTB# function is selected, the 16X Baud rate clock
output is available at this pin.
3) RXRDYB# - RXRDYB# (active low) is intended for monitoring DMA data transfers.
See Table 2 on page 7 for more details.
TXA
TXB
38
26
O
UART channel A or B Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be a
logic 1 during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is a logic 0. If it is not used, leave it unconnected.
RXA
RXB
39
25
I
UART channel A or B Receive Data or infrared receive data. Normal receive data
input must idle at logic 1 condition. The infrared receiver pulses typically idles at logic
0 but can be inverted by software control prior going in to the decoder, see MCR[6]
and FCTR[2]. If this pin is not used, tie to VCC or pull it high via a 100k ohm resistor.
RTSA#
RTSB#
36
23
O
UART channel A or B Request-to-Send (active low) or general purpose output. This
output must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
FCTR[1:0], EMSR[5:4] and IER[6].
CTSA#
CTSB#
40
28
I
UART channel A or B Clear-to-Send (active low) or general purpose input. It can be
used for auto CTS flow control, see EFR[7], and IER[7]. This input should be con-
nected to VCC when not used.
DTRA#
DTRB#
37
27
O
UART channel A or B Data-Terminal-Ready (active low) or general purpose output. If
this pin is not used, leave it unconnected.
DSRA#
DSRB#
41
29
I
UART channel A or B Data-Set-Ready (active low) or general purpose input. This
input should be connected to VCC when not used. This input has no effect on the
UART.
CDA#
CDB#
42
30
I
UART channel A or B Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
RIA#
RIB#
43
31
I
UART channel A or B Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
ANCILLARY SIGNALS
XTAL1
11
I
Crystal or external clock input.
XTAL2
13
O
Crystal or buffered clock output.
RESET
21
I
Reset (active high) - A longer than 40 ns logic 1 pulse on this pin will reset the internal
registers and all outputs. The UART transmitter output will be held at logic 1, the
receiver input will be ignored and outputs are reset during reset period (see External
Reset Conditions).
VCC
44, 33
Pwr
3.3V or 5V power supply. Please note that the inputs are not 5V tolerant when oper-
ating at 3.3V.
N
AME
44-PLCC
P
IN
#
T
YPE
D
ESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C2852CJ | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2852IJ | 3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C850CJ | UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control |
| XR16C850CM | UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control |
| XR16C850CP | UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2852_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS |
| XR16C2852CJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16C2852CJ-0A-EB | 功能描述:UART 接口集成電路 Supports C2852 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2852CJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2852CJTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。