參數資料
型號： XR16C2852
廠商： Exar Corporation
英文描述： 3.3V AND 5V DUART WITH 128-BYTE FIFO
中文描述： 3.3V和5V杜阿爾特128字節FIFO
文件頁數： 21/42頁
文件大?。?/td> 574K
代理商： XR16C2852
XR16C2852
REV. 2.0.0
3.3V AND 5V DUART WITH 128-BYTE FIFO
á
21
ISR register status bit and the interrupt will be
cleared when the FIFO drops below the trigger
level.
C.
The receive data ready bit (LSR BIT-0) is set as
soon as a character is transferred from the shift
register to the receive FIFO. It is reset when the
FIFO is empty.
4.4.2
IER versus Receive/Transmit FIFO Polled
Mode Operation
When FCR BIT-0 equals a logic 1 for FIFO enable; re-
setting IER bits 0-3 enables the XR16C2852 in the
FIFO polled mode of operation. Since the receiver
and transmitter have separate bits in the LSR either
or both can be used in the polled mode by selecting
respective transmit or receive control bit(s).
A.
LSR BIT-0 indicates there is data in RHR
or
RX
FIFO.
B.
LSR BIT-1 indicates an overrun error has oc-
curred and that data in the FIFO may not be valid.
C.
LSR BIT 2-4 provides the type of receive data er-
rors encountered for the data byte in RHR, if any.
D.
LSR BIT-5 indicates THR is empty.
E.
LSR BIT-6 indicates when both the transmit FIFO
and TSR are empty.
F.
LSR BIT-7 indicates a data error in at least one
character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when
RHR has a data character in the non-FIFO mode
or
when the receive FIFO has reached the programmed
trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt
(default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is
issued whenever the THR becomes empty in the non-
FIFO mode or when data in the FIFO falls below the
programmed trigger level in the FIFO mode. If the
THR is empty when this bit is enabled, an interrupt
will be generated.
Logic 0 = Disable Transmit Ready interrupt
(default).
Logic 1 = Enable Transmit Ready interrupt.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1,
it will generate an interrupt to inform the host control-
ler about the error status of the current data byte in
FIFO. LSR bits 1-4 generate an interrupt immediately
when the character has been received.
Logic 0 = Disable the receiver line status interrupt
(default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register inter-
rupt (default).
Logic 1 = Enable the modem status register inter-
rupt.
IER[4]: Sleep Mode Enable (requires EFR bit-4 =
1)
Logic 0 = Disable Sleep Mode (default).
Logic 1 = Enable Sleep Mode. See Sleep Mode
section for further details.
IER[5]: Xoff Interrupt Enable (requires EFR bit-
4=1)
Logic 0 = Disable the software flow control, receive
Xoff interrupt. (default)
Logic 1 = Enable the software flow control, receive
Xoff interrupt. See Software Flow Control section
for details.
IER[6]: RTS# Output Interrupt Enable (requires
EFR bit-4=1)
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART
issues an interrupt when the RTS# pin makes a
transition from low to high.
IER[7]: CTS# Input Interrupt Enable (requires EFR
bit-4=1)
Logic 0 = Disable the CTS# interrupt (default).
Logic 1 = Enable the CTS# interrupt. The UART
issues an interrupt when CTS# pin makes a transi-
tion from low to high.
4.5
I
NTERRUPT
S
TATUS
R
EGISTER
(ISR) - R
EAD
-
O
NLY
The UART provides multiple levels of prioritized inter-
rupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with
six interrupt status bits. Performing a read cycle on
the ISR will give the user the current highest pending
interrupt level to be serviced, others are queued up to
be serviced next. No other interrupts are acknowl-
edged until the pending interrupt is serviced. The In-
terrupt Source Table, Table 9, shows the data values
(bit 0-5) for the interrupt priority levels and the inter-
rupt sources associated with each of these interrupt
levels.
相關PDF資料
PDF描述
XR16C2852CJ 3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2852IJ 3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C850CJ UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850CM UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850CP UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
相關代理商/技術參數
參數描述
XR16C2852_05 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
XR16C2852CJ 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16C2852CJ-0A-EB 功能描述:UART 接口集成電路 Supports C2852 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C2852CJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C2852CJTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*