REV. 2.3.1 28 4.3.2 IER versus Receive/Transmit FIFO Polled Mode Operation When FCR BIT-0 equ" />
參數資料
型號： XR16C850CM-F
廠商： Exar Corporation
文件頁數： 21/56頁
文件大?。?/td> 0K
描述： IC UART FIFO 128B 48TQFP
標準包裝： 250
特點： *
通道數： 1，UART
FIFO's： 128 字節
規程： RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
其它名稱： 1016-1658
XR16C850CM-F-ND
XR16C850
xr
2.97V TO 5.5V UART WITH 128-BYTE FIFO
REV. 2.3.1
28
4.3.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16C850 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can
be used in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR or RX FIFO.
B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR BIT-5 indicates THR is empty.
E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is issued whenever the THR becomes empty in the non-
FIFO mode or when data in the FIFO falls below the programmed trigger level in the FIFO mode. If the THR is
empty when this bit is enabled, an interrupt will be generated. Reading ISR will clear this interrupt. It is not
necessary to disable this interrupt by setting IER bit-1 = 0. The UART will automatically issue this interrupt
again when more data is loaded into the FIFO and the FIFO level drops below the trigger level and/or it
becomes empty.
Logic 0 = Disable Transmit Ready interrupt (default).
Logic 1 = Enable Transmit Ready interrupt.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when the
character has been received. LSR bits 2-4 generate an interrupt when the character with errors is read out of
the FIFO.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[4]: Sleep Mode Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Sleep Mode (default).
Logic 1 = Enable Sleep Mode. See Sleep Mode section for further details.
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
相關PDF資料
PDF描述
XR16L2750IM-F IC UART FIFO 64B DUAL 48TQFP
ST16C2550CQ48-F IC DUART FIFO 16B 48TQFP
XR88C681CP/40-F IC UART CMOS DUAL 40PDIP
AT89C51RB2-RLRIM IC MCU FLASH 8051 16K 5V 44-VQFP
XR16V2550IM-F IC UART FIFO 16B 48TQFP
相關代理商/技術參數
參數描述
XR16C850CMTR-F 功能描述:UART 接口集成電路 UART w/128 Bytes FIFO & IrDA RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C850CP 制造商:EXAR 制造商全稱:EXAR 功能描述:UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:UART with 128-byte FIFO’s FIFO Counters and Half-duplex Control
XR16C850IJ 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART WITH 128-BYTE FIFO
XR16C850IJ-F 功能描述:UART 接口集成電路 UARTW/128BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*