- 您現在的位置：買賣IC網 > PDF目錄1974 > XR16C864IQ-F (Exar Corporation)IC UART FIFO 128B QUAD 100QFP PDF資料下載
參數資料
| 型號： | XR16C864IQ-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 26/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 128B QUAD 100QFP |
| 標準包裝： | 66 |
| 特點： | * |
| 通道數： | 4，QUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-QFP（14x20） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1277 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16C864
32
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
REV. 2.2.0
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: OP1# Output or RS485 Output Control
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal. If Auto RS-485
Half-Duplex direction control is enabled via FCTR bit-3, MCR bit-2 should not be written to.
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be set to a logic zero during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During loopback mode, it sets
OP2# internally to a logic 1.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During loopback mode, it sets OP2# internally
to a logic 0.
TABLE 13: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2450IJ-F | IC UART FIFO 1B DUAL 44PLCC |
| XR16L2550IJ-F | IC UART FIFO 16B DUAL 44PLCC |
| XR16L2551IM-F | IC UART FIFO 16B DUAL 48TQFP |
| XR16L2552IJ-F | IC UART FIFO 16B DUAL 44PLCC |
| XR16L2750IJ-F | IC UART FIFO 64B DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C864IQTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C872 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER |
| XR16C872CQ | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER |
| XR16C872IQ | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER |
| XR16L2450 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART |
發布緊急采購，3分鐘左右您將得到回復。