參數資料
型號： XR16C864IQ-F
廠商： Exar Corporation
文件頁數： 31/51頁
文件大小： 0K
描述： IC UART FIFO 128B QUAD 100QFP
標準包裝： 66
特點： *
通道數： 4，QUART
FIFO's： 128 字節
規程： RS232，RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 100-BQFP
供應商設備封裝： 100-QFP（14x20）
包裝： 托盤
其它名稱： 1016-1277
XR16C864
37
REV. 2.2.0
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
4.13
Baud Rate Generator Registers (DLL and DLM) - Read/Write
The concatenation of the contents of DLM and DLL gives the 16-bit divisor value which is used to calculate the
baud rate:
Baud Rate = (Clock Frequency / 16) / Divisor
See MCR bit-7 and the baud rate table also.
4.14
Device Identification Register (DVID) - Read Only
This register contains the device ID (0x14 for XR16C864). Prior to reading this register, DLL and DLM should
be set to 0x00.
4.15
Device Revision Register (DREV) - Read Only
This register contains the device revision information. For example, 0x01 means revision A. Prior to reading
this register, DLL and DLM should be set to 0x00.
4.16
Trigger Level (TRG) - Write-Only
User Programmable Transmit/Receive Trigger Level Register.
TRG[7:0]: Trigger Level Register
These bits are used to program desired trigger levels when trigger Table-D is selected. FCTR bit-7 selects
between programming the RX Trigger Level (a logic 0) and the TX Trigger Level (a logic 1).
4.17
FIFO Data Count Register (FC) - Read-Only
This register is accessible when LCR = 0xBF. Note that this register is not identical to the FIFO Level Count
Register which is located in the general register set when FCTR bit-6 = 1 (Scratchpad Register Swap). It is
suggested to read the FIFO Level Count Register at the Scratchpad Register location when FCTR bit-6 = 1.
See
Table 14.
FC[7:0]: FIFO Data Count Register
Transmit/Receive FIFO Count. Number of characters in Transmit (FCTR[7] = 1) or Receive FIFO (FCTR[7] =
0) can be read via this register.
4.18
Feature Control Register (FCTR) - Read/Write
This register controls the XR16C864 new functions that are not available in ST16C554 or ST16C654.
FCTR[1:0]: RTS Hysteresis
User selectable RTS# hysteresis levels for hardware flow control application. After reset, these bits are set to
“0” to select the next trigger level for hardware flow control. See
Table 15 for more details.
FCTR[2]: IrDA RX Inversion
Logic 0 = Select RX input as encoded IrDA data (Idle state will be logic 0).
Logic 1 = Select RX input as inverted encoded IrDA data (Idle state will be logic 1).
FCTR[3]: Auto RS-485 Direction Control
Logic 0 = OP1# can be used as a general purpose output and can be controlled via MCR bit-2.
Logic 1 = OP1# is used as the Auto RS-485 half-duplex direction control output. The TX Ready Interrupt
behavior also changes. See
Table 3.
相關PDF資料
PDF描述
XR16L2450IJ-F IC UART FIFO 1B DUAL 44PLCC
XR16L2550IJ-F IC UART FIFO 16B DUAL 44PLCC
XR16L2551IM-F IC UART FIFO 16B DUAL 48TQFP
XR16L2552IJ-F IC UART FIFO 16B DUAL 44PLCC
XR16L2750IJ-F IC UART FIFO 64B DUAL 44PLCC
相關代理商/技術參數
參數描述
XR16C864IQTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C872 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16C872CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16C872IQ 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16L2450 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*