REV. 1.2.1 8 2.6 Channel A and B Internal Registers Each UART channel in the 2752 has a set " />
參數資料
型號： XR16L2752IJ-F
廠商： Exar Corporation
文件頁數： 48/49頁
文件大?。?/td> 0K
描述： IC UART FIFO 64B DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS485
電源電壓： 2.25 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1650
XR16L2752IJ-F-ND
XR16L2752
xr
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.2.1
8
2.6
Channel A and B Internal Registers
Each UART channel in the 2752 has a set of enhanced registers for control, monitoring and data loading and
unloading. The configuration register set is compatible to those already available in the standard single
16C550 and dual ST16C2550. These registers function as data holding registers (THR/RHR), interrupt status
and control registers (ISR/IER), a FIFO control register (FCR), receive line status and control registers (LSR/
LCR), modem status and control registers (MSR/MCR), programmable data rate (clock) divisor registers (DLL/
DLM), and a user accessible Scratchpad Register (SPR).
Beyond the general 16C2550 features and capabilities, the 2752 offers enhanced feature registers (AFR,
EMSR, FLVL, EFR, Xon/Xoff 1, Xon/Xoff 2, FCTR, TRG, FC) that provide automatic RTS and CTS hardware
flow control, Xon/Xoff software flow control, automatic RS-485 half-duplex direction output enable/disable,
FIFO trigger level control, FIFO level counters, and simultaneous writes to both channels. All the register
functions are discussed in full detail later in “Section 3.0, UART INTERNAL REGISTERS” on page 20.
2.7
Simultaneous Write to Channel A and B
During a write mode cycle, the setting of Alternate Function Register (AFR) bit-0 to a logic 1 will override the
CHSEL selection and allows a simultaneous write to both UART channel sections. This functional capability
allow the registers in both UART channels to be modified concurrently, saving individual channel initialization
time. Caution should be considered, however, when using this capability. Any in-process serial data transfer
may be disrupted by changing an active channel’s mode.
2.8
DMA Mode
The device does not support direct memory access. The DMA Mode (a legacy term) in this document doesn’t
mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of
the RXRDY# A/B (MF# A/B becomes RXRDY# A/B output when AFR[2:1] = ‘10’) and TXRDY# A/B output
pins. The transmit and receive FIFO trigger levels provide additional flexibility to the user for block mode
operation. The LSR bits 5-6 provide an indication when the transmitter is empty or has an empty location(s) for
more data. The user can optionally operate the transmit and receive FIFO in the DMA mode (FCR bit-3=1).
When the transmit and receive FIFO are enabled and the DMA mode is disabled (FCR bit-3 = 0), the 2752 is
placed in single-character mode for data transmit or receive operation. When DMA mode is enabled (FCR bit-
3 = 1), the user takes advantage of block mode operation by loading or unloading the FIFO in a block
sequence determined by the programmed trigger level. In this mode, the 2752 sets the TXRDY# pin when the
transmit FIFO becomes full, and sets the RXRDY# pin when the receive FIFO becomes empty. The following
table shows their behavior. Also see Figures 18 through 23.
TABLE 1: CHANNEL A AND B SELECT
CS#
CHSEL
FUNCTION
1
X
UART de-selected
0
1
Channel A selected
0
Channel B selected
TABLE 2: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR Bit-3 = 0
(DMA Mode Disabled)
FCR Bit-3 = 1
(DMA Mode Enabled)
RXRDY# A/B LOW = 1 byte.
HIGH = no data.
LOW = at least 1 byte in FIFO.
HIGH = FIFO empty.
HIGH to LOW transition when FIFO reaches the
trigger level, or time-out occurs.
LOW to HIGH transition when FIFO empties.
TXRDY# A/B LOW = THR empty.
HIGH = byte in THR.
LOW = FIFO empty.
HIGH = at least 1 byte in FIFO.
LOW = FIFO has at least 1 empty location.
HIGH = FIFO is full.
相關PDF資料
PDF描述
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
ST16C552ACJ68-F IC UART FIFO 16B DUAL 68PLCC
ST16C650ACJ44-F IC UART FIFO 32B 44PLCC
XR20M1170IG24-F IC UART FIFO I2C/SPI 64B 24TSSOP
相關代理商/技術參數
參數描述
XR16L2752IJTR-F 制造商:Exar Corporation 功能描述:XR16L2752 Series 6.25 Mbps 5.5 V Dual UART With 64-Byte FIFO - PLCC-44
XR16L570 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L570_07 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L570IL24 功能描述:UART 接口集成電路 UART w/ POWER SAVE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L570IL24-0B-EB 功能描述:UART 接口集成電路 Supports L570 24 pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*