- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L788CQ (EXAR CORP) HIGH PERFORMANCE OCTAL UART PDF資料下載
參數資料
| 型號： | XR16L788CQ |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH PERFORMANCE OCTAL UART |
| 中文描述： | 8 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3 MM HEIGHT, PLASTIC, QFP-100 |
| 文件頁數： | 20/42頁 |
| 文件大?。?/td> | 557K |
| 代理商： | XR16L788CQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
áyyyyyyyyyyyy
XR16L788 OCTAL UART
REV. 1.1.4
20
N
OTE
2:
MCR bits 2 and 3 (OP1 and OP2 outputs) are not
available in the XR16L788. They are present for 16C550
compatibility during Internal loopback, see Figure 10.
4.6
T
RANSMITTER
The transmitter section comprises of 64 bytes of
FIFO, a byte-wide Transmit Holding Register (THR)
and an 8-bit Transmit Shift Register (TSR). THR re-
ceives a data byte from the host (non-FIFO mode) or
a data byte from the FIFO
when the FIFO is enabled
by FCR bit-0. TSR shifts out every data bit with the
16X or 8X internal clock. A bit time is 16 or 8 clock pe-
riods. The transmitter sends the start bit followed by
the number of data bits, inserts the proper parity bit if
enabled, and adds the stop bit(s). The status of the
THR and TSR are reported in the Line Status Regis-
ter (LSR bit-5 and bit-6).
4.6.1
Transmit Holding Register (THR)
The transmit holding register is an 8-bit register pro-
viding a data interface to the host processor. The host
writes transmit data byte to the THR to be converted
into a serial data stream including start-bit, data bits,
parity-bit and stop-bit(s). The least-significant-bit (Bit-
0) becomes first data bit to go out. The THR is also
the input register to the transmit FIFO of 64 bytes
when FIFO operation is enabled by FCR bit-0. Every
time a write operation is made to the transmit holding
register, its FIFO data pointer is automatically
bumped to the next sequential data location. A THR
empty interrupt can be generated when IER bit-1 is
set to logical 1.
4.6.2
Transmitter Operation in non-FIFO
The host loads transmit data to THR one character at
a time. The THR empty flag (LSR bit-5) is set when
the data byte is transferred to TSR. THR flag can
generate a transmit empty interrupt (ISR bit-1) when
it is enabled by IER bit-1. The TSR flag (LSR bit-6) is
set when TSR becomes completely empty.
4.6.3
The host may fill the transmit FIFO with up to 64
bytes of transmit data. The THR empty flag (LSR bit-
5) is set whenever the FIFO is empty. The THR emp-
ty flag can generate a transmit empty interrupt (ISR
bit-1) when the amount of data in the FIFO falls below
its programmed trigger level (see TXTRG register).
The transmit empty interrupt is enabled by IER bit-1.
The TSR flag (LSR bit-6) is set when TSR becomes
completely empty. Furthermore, with the RS485 half-
duplex direction control enabled (FCTR bit-5=1), the
source of the transmit empty interrupt changes to
TSR empty instead of THR empty. This is to ensure
the RTS# output is not changed until the last stop bit
of the last character is shifted out.
Transmitter Operation in FIFO
4.6.4
The auto RS485 half-duplex direction control chang-
es the behavior of the transmitter when enabled by
FCTR bit-5. It de-asserts RTS# or DTR# after a spec-
ified delay indicated in MSR[7:4] following
the last
stop bit of the last character that has been transmit-
ted. This helps in turning around the transceiver to re-
ceive the remote station’s response. The delay opti-
mizes the time needed for the last transmission to
reach the farthest station on a long cable network be-
fore switching off the line driver. This delay prevents
undesirable line signal disturbance that causes signal
degradation. The auto RS485 half-duplex direction
control also changes the transmitter empty interrupt
to TSR empty instead of THR empty.
Auto RS485 Operation
F
IGURE
11. T
RANSMITTER
O
PERATION
IN
NON
-FIFO M
ODE
Transmit
Holding
Register
(THR)
Transmit Shift Register (TSR)
Data
Byte
L
S
B
M
S
B
THR Interrupt (ISR bit-1)
Enabled by IER bit-1
TXNOFIFO1
16X or 8X
Clock
(8XMODE
Register)
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L788IQ | HIGH PERFORMANCE OCTAL UART |
| XR17C154 | Tip, Offset Tapered Needle, 1mm Diameter |
| XR17C154CV | Burner |
| XR17C154IV | Tools, Heatgun; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No |
| XR17C158 | PCI Bus Octal UART(八通用異步接收器/發送器（滿足通訊系統中PCI總線和高帶寬要求）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L788CQ-0A-EVB | 功能描述:UART 接口集成電路 Supports L788 100 ld QFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L788CQ-0B-EVB | 功能描述:界面開發工具 Supports L788 100 ld QFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16L788CQ-F | 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L788CQTR-F | 功能描述:UART 接口集成電路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L788IQ | 制造商:Exar Corporation 功能描述:3.3V OCTAL UART |
發布緊急采購，3分鐘左右您將得到回復。