參數資料
型號： XR16L788CQ
廠商： EXAR CORP
元件分類： 微控制器/微處理器
英文描述： HIGH PERFORMANCE OCTAL UART
中文描述： 8 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP100
封裝： 14 X 20 MM, 3 MM HEIGHT, PLASTIC, QFP-100
文件頁數： 23/42頁
文件大?。?/td> 557K
代理商： XR16L788CQ
XR16L788 OCTAL UART
á
REV. 1.1.4
23
grammed trigger level. It will be cleared when the
FIFO drops below the programmed trigger level.
B.
FIFO level will be reflected in the ISR register
when the FIFO trigger level is reached. Both the
ISR register status bit and the interrupt will be
cleared when the FIFO drops below the trigger
level.
C.
The receive data ready bit (LSR BIT-0) is set as
soon as a character is transferred from the shift
register to the receive FIFO. It is reset when the
FIFO is empty.
4.10 IER
VERSUS
R
ECEIVE
/T
RANSMIT
FIFO P
OLLED
M
ODE
O
PERATION
When FCR BIT-0 equals a logic 1 for FIFO enable;
resetting IER bits 0-3 enables the XR16L788 in the
FIFO polled mode of operation. Since the receiver
and transmitter have separate bits in the LSR either
or both can be used in the polled mode by selecting
respective transmit or receive control bit(s).
A.
LSR BIT-0 indicates there is data in RHR
or
RX
FIFO.
B.
LSR BIT 1-4 provides the type of receive data er-
rors encountered for the data byte in RHR, if any.
C.
LSR BIT-5 indicates THR is empty.
D.
LSR BIT-6 indicates when both the transmit FIFO
and TSR are empty.
E.
LSR BIT-7 indicates the Or’ed function of errors
in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when
RHR has a data character in the non-FIFO mode
or
when the receive FIFO has reached the programmed
trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt.
(default)
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This interrupt is associated with bit-5 in the LSR reg-
ister. An interrupt is issued whenever the THR be-
comes empty or when data in the FIFO falls below
the programmed trigger level.
Logic 0 = Disable Transmit Holding Register empty
interrupt. (default)
Logic 1 = Enable Transmit Holding Register empty in-
terrupt.
IER[2]: Receive Line Status Interrupt Enable
Any of the LSR register bits 1,2,3 or 4 becomes ac-
tive will generate an interrupt to inform the host con-
troller about the error status of the current data byte
in FIFO.
Logic 0 = Disable the receiver line status interrupt.
(default)
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt.
(default)
Logic 1 = Enable the modem status register interrupt.
IER[4]: Reserved
.
IER[5]: Xoff Interrupt Enable (requires EFR bit-
4=1)
Logic 0 = Disable the software flow control, receive
Xoff interrupt. (default)
Logic 1 = Enable the software flow control, receive
Xoff interrupt. See Software Flow Control section for
details.
IER[6]: RTS# Output Interrupt Enable (requires
EFR bit-4=1)
Logic 0 = Disable the RTS# interrupt. (default).
Logic 1 = Enable the RTS# interrupt. The UART is-
sues an interrupt when the RTS# pin makes a transi-
tion.
IER[7]: CTS# Input Interrupt Enable (requires EFR
bit-4=1)
Logic 0 = Disable the CTS# interrupt. (default).
Logic 1 = Enable the CTS# interrupt. The UART is-
sues an interrupt when CTS# pin makes a transition.
4.11 I
NTERRUPT
S
TATUS
R
EGISTER
(ISR)
The UART provides multiple levels of prioritized inter-
rupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with
six interrupt status bits. Performing a read cycle on
the ISR will give the user the current highest pending
interrupt level to be serviced, others queue up for
next service. No other interrupts are acknowledged
until the pending interrupt is serviced. The Interrupt
Source Table, Table 9, shows the data values (bit 0-5)
for the six prioritized interrupt levels and the interrupt
sources associated with each of these interrupt lev-
els.
4.11.1 Interrupt Generation:
LSR is by any of the LSR bits 1, 2, 3 and 4.
RXRDY is by RX trigger level.
RXRDY Time-out is by the a 4-char plus 12 bits
delay timer if data doesn’t reach FIFO trigger level.
TXRDY is by LSR bit-5 (or bit-6 in auto RS485 con-
trol).
相關PDF資料
PDF描述
XR16L788IQ HIGH PERFORMANCE OCTAL UART
XR17C154 Tip, Offset Tapered Needle, 1mm Diameter
XR17C154CV Burner
XR17C154IV Tools, Heatgun; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No
XR17C158 PCI Bus Octal UART(八通用異步接收器/發送器（滿足通訊系統中PCI總線和高帶寬要求）)
相關代理商/技術參數
參數描述
XR16L788CQ-0A-EVB 功能描述:UART 接口集成電路 Supports L788 100 ld QFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788CQ-0B-EVB 功能描述:界面開發工具 Supports L788 100 ld QFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16L788CQ-F 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788CQTR-F 功能描述:UART 接口集成電路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788IQ 制造商:Exar Corporation 功能描述:3.3V OCTAL UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*