- 您現在的位置：買賣IC網 > PDF目錄16433 > XR16M698IQ-0A-EVB (Exar Corporation)EVAL BOARD FOR M698-A 100QFP PDF資料下載
參數資料
| 型號： | XR16M698IQ-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 35/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR M698-A 100QFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
XR16M698
40
1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO
REV. 1.0.0
MCR[3]: Send Char Immediate (OP2 in Local Loopback Mode)
This bit is used to transmit a character immediately irrespective of the bytes currently in the transmit FIFO. The
data byte must be loaded into the transmit holding register (THR) immediately following the write to this bit (to
set it to a ’1’). In other words, no other register must be accessed between setting this bit and writing to the
THR. The loaded byte will be transmitted ahead of all the bytes in the TX FIFO, immediately after the character
currently being shifted out of the transmit shift register is sent out. The existing line parameters (parity, stop
bits) will be used when composing the character. This bit is self clearing, therefore, must be set before sending
a custom characer each time. Please note that the Transmitter must be enabled for this function (MSR[3] = 0).
Also, if software flow control is enabled, the software flow control characters (Xon, Xoff) have higher priority
and will get shifted out before the custom byte is transmitted.
Logic 0 = Send Char Immediate disabled (default).
Logic 1 = Send Char Immediate enabled.
In Local Loopback Mode (MCR[4] = 1), this bit acts as the legacy OP2 output and controls the CD bit in the
MSR register as shown in Figure 11. Please make sure that this bit is a ’0’ when exiting the Local Loopback
Mode.
MCR[2]: DTR# or RTS# for Auto Flow Control (OP1 in Local Loopback Mode)
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit-6. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
In Local Loopback mode (MCR[4] = 1), this bit acts as the legacy OP1 output and controls the RI bit in the MSR
register, as shown in Figure 11.
MCR[1]: RTS# Output
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[0]: DTR# Output
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the
modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
4.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit-2 is set to a logic
1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity,
framing, overrun, break).
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there are no more errors in the FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| A3BBB-3018G | IDC CABLE- ASR30B/AE30G/ASR30B |
| VI-2V1-EX | CONVERTER MOD DC/DC 12V 75W |
| EBM18DCCT | CONN EDGECARD 36POS R/A .156 SLD |
| CM322522-680KL | INDUCTOR 68UH 65MA SMD |
| VI-27T-EX | CONVERTER MOD DC/DC 6.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M698IQ-0B-EVB | 功能描述:界面開發工具 Eval Board for XR16M698IQ-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M698IQ100 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO |
| XR16M698IQ100-F | 功能描述:UART 接口集成電路 8-ch 32-byte UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M698IQ100TR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 32Byte FIFO 1.8V/2.5V/3.3V 100-Pin PQFP T/R 制造商:Exar Corporation 功能描述:XR16M698IQ100TR-F |
| XR16M752 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。