參數資料
型號: XR16V798IQ-0A-EVB
廠商: Exar Corporation
文件頁數: 11/56頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR16V798-A 100QFP
設計資源: XR17V798/794 Eval Board Schematic
標準包裝: 1
系列: *
XR16V798
19
REV. 1.0.1
HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL BAUD RATE
2.15
Sleep Mode with Auto Wake-Up
The 798 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the 798 to enter sleep mode:
no interrupts pending for all 8 channels of the 798 (ISR bit-0 = 1)
SLEEP register = 0xFF
modem inputs are not toggling (MSR bits 0-3 = 0)
RX input pin of all 8 channels are idling HIGH
The 798 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no
clock output as an indication that the device has entered the sleep mode.
The 798 resumes normal operation by any of the following:
a receive data start bit transition (HIGH to LOW)
a data byte is loaded to the transmitter, THR or FIFO
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the 798 is awakened by any one of the above conditions, it will generate an interrupt. If the interrupt for the
event that woke up the 798 is not enabled, then a special wake-up interrupt occurs where reading the interrupt
status register will return a "no interrupt" indication. For example, there is a change of state on the CTS# input
that wakes up the 798, but the MSR interrupt is not enabled. Reading the interrupt status register will return a
value indicating that there are no pending interrupts and will clear the wake-up interrupt.
The 798 will return to the sleep mode automatically after all interrupting conditions have been serviced and
cleared. If the 798 is awakened by the modem inputs, a read to the MSR is required to reset the modem inputs.
In any case, the sleep mode will not be entered while an interrupt is pending in any channel. The 798 will stay
in the sleep mode of operation until it is disabled by setting SLEEP = 0x00.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate.
相關PDF資料
PDF描述
XR16V698IQ-0B-EVB EVAL BOARD FOR XR16V698-B 100QFP
XR16V698IQ-0A-EVB EVAL BOARD FOR XR16V698-A 100QFP
KIT33972AEWEVBE KIT EVALUATION FOR MC33972
EBM31DCMS CONN EDGECARD 62POS .156 WW
VI-J1L-EX CONVERTER MOD DC/DC 28V 75W
相關代理商/技術參數
參數描述
XR16V798IQ-0B-EVB 功能描述:UART 接口集成電路 Supports V798 100 ld QFP,PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V798IQ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V798IQTR-F 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 2.5V/3.3V 100-Pin PQFP T/R
XR-1790 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Audio Schematic
XR17C152 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART