參數資料
型號： XR16V798IQ-0A-EVB
廠商： Exar Corporation
文件頁數： 26/56頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16V798-A 100QFP
設計資源： XR17V798/794 Eval Board Schematic
標準包裝： 1
系列： *
XR16V798
32
HIGH PERFORMANCE 2.25V TO 3.6V OCTAL UART WITH FRACTIONAL BAUD RATE
REV. 1.0.1
4.4
Interrupt Status Register (ISR) - Read Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others queue up for next
service. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt Source
Table, Table 13, shows the data values (bit 0-5) for the six prioritized interrupt levels and the interrupt sources
associated with each of these interrupt levels.
4.4.1
Interrupt Generation:
LSR is by any of the LSR bits 1, 2, 3 and 4. See IER bit-2 description above.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX trigger level or TX FIFO empty (or transmitter empty in auto RS-485 control).
MSR is by any of the MSR bits 0, 1, 2 and 3.
Receive Xon/Xoff/Special character is by detection of a Xon, Xoff or Special character.
CTS#/DSR# is when its transmitter toggles the input pin (from LOW to HIGH) during auto CTS/DSR flow
control enabled by EFR bit-7 and selection on MCR bit-2.
RTS#/DTR# is when its receiver toggles the output pin (from LOW to HIGH) during auto RTS/DTR flow
control enabled by EFR bit-6 and selection on MCR bit-2.
4.4.2
Interrupt Clearing:
LSR interrupt is cleared by a read to the LSR register.
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR.
TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
MSR interrupt is cleared by a read to the MSR register.
Xon or Xoff interrupt is cleared by a read to ISR register.
Special character interrupt is cleared by a read to ISR or after the next character is received.
RTS#/DTR# and CTS#/DSR# status change interrupts are cleared by a read to the MSR register.
]
TABLE 13: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF THE INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Received Data Ready)
3
0
1
0
RXRDY (Receive Data Time-out)
4
0
1
0
TXRDY (Transmitter Holding Register Empty)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xon/Xoff or Special character)
7
1
0
CTS#/DSR#, RTS#/DTR# change of state
X
0
1
None (default) or wake-up indicator
相關PDF資料
PDF描述
XR16V698IQ-0B-EVB EVAL BOARD FOR XR16V698-B 100QFP
XR16V698IQ-0A-EVB EVAL BOARD FOR XR16V698-A 100QFP
KIT33972AEWEVBE KIT EVALUATION FOR MC33972
EBM31DCMS CONN EDGECARD 62POS .156 WW
VI-J1L-EX CONVERTER MOD DC/DC 28V 75W
相關代理商/技術參數
參數描述
XR16V798IQ-0B-EVB 功能描述:UART 接口集成電路 Supports V798 100 ld QFP,PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V798IQ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V798IQTR-F 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 2.5V/3.3V 100-Pin PQFP T/R
XR-1790 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Audio Schematic
XR17C152 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*