- 您現在的位置：買賣IC網 > PDF目錄376455 > XR17D158CV (EXAR CORP) UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART PDF資料下載
參數資料
| 型號： | XR17D158CV |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| 中文描述： | 8 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144 |
| 文件頁數： | 40/72頁 |
| 文件大?。?/td> | 1520K |
| 代理商： | XR17D158CV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
XR17D158
UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART
xr
REV. 1.2.1
40
5.8.4
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR) register and
also encoded in INT (INT0-INT3) register in the Device Configuration Registers.
IER
VERSUS
R
ECEIVE
FIFO I
NTERRUPT
M
ODE
O
PERATION
When the receive FIFO (FCR bit-0 = a logic 1) and receive interrupts (IER BIT-0 = logic 1) are enabled, the
RHR interrupts (see ISR bits 3 and 4) status will reflect the following:
A.
The receive data available interrupts are issued to the host when the FIFO has reached the programmed
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
B.
FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
C.
The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to
the receive FIFO. It is reset when the FIFO is empty.
IER
VERSUS
R
ECEIVE
/T
RANSMIT
FIFO P
OLLED
M
ODE
O
PERATION
When FCR BIT-0 equals a logic 1 for FIFO enable, resetting IER bits 0-3 enables the 158 in the FIFO polled
mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can be used
in the polled mode by selecting respective transmit or receive control bit(s).
A.
LSR BIT-0 indicates there is data in RHR
or
RX FIFO.
B.
LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C.
LSR BITS 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D.
LSR BIT-5 indicates THR is empty.
E.
LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F.
LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode
or when
the receive FIFO has reached the programmed trigger level in the FIFO mode. A receive data timeout interrupt
will be issued in the FIFO mode when the receive FIFO has not reached the programmed trigger level and the
RX input has been idle for 4 character + 12 bit times.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
When Auto RS485 mode operation is disabled (FCTR bit-5 = 0), this interrupt is associated with bit-5 in the
LSR register. An interrupt is issued whenever the THR becomes empty or when data in the FIFO falls below
the programmed trigger level. When Auto RS485 mode operation is enabled (FCTR bit-5 = 1), this interrupt is
associated with bit-6 in the LSR register. An interrupt is issued whenever the TX FIFO and the TSR becomes
empty.
Logic 0 = Disable Transmit Holding Register empty interrupt (default).
Logic 1 = Enable Transmit Holding Register empty interrupt.
IER[2]: Receive Line Status Interrupt Enable
Any of LSR register bits 1, 2, 3 or 4 will generate an LSR interrupt immediately when a character received by
the RX FIFO has an error.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
Interrupt Enable Register (IER) - Read/Write
相關PDF資料 |
PDF描述 |
|---|---|
| XR17L152IM | CAP .068UF 400V PEN FILM 2825 5% |
| XR17L152 | 3.3V PCI BUS DUAL UART |
| XR17L152CM | 3.3V PCI BUS DUAL UART |
| XR2001 | High-Voltage, High-Current Darlington Transistor Arrays |
| XR2002CN | High-Voltage, High-Current Darlington Transistor Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17D158CV-0A-EVB | 功能描述:界面開發工具 Supports D158 144 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17D158CV-F | 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D158CV-F-SIWI | 制造商:Exar Corporation 功能描述:FOR WILLIAMS GAMING THEIR CM'S 制造商:EXAR 功能描述:XR17D158CV-F-SIWI 制造商:EXAR 功能描述:FOR WILLIAMS GAMING THEIR CM'S |
| XR17D158CVTR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D158CVTR-F |
| XR17D158IV | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。