- 您現在的位置：買賣IC網 > PDF目錄16512 > XR19L212IL48-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L202 48QFN PDF資料下載
參數資料
| 型號： | XR19L212IL48-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 10/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR19L202 48QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
XR19L212
18
TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.1
2.16
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 15), the L212 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the L212 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the L212 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the L212 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to a logic 0. Following reset the user
can write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/
Xoff characters (See Table 15) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters
are selected, the L212 compares two consecutive receive characters with two software flow control 8-bit
values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow
control mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or
FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the L212 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The L212 sends the
Xoff-1,2 characters two-character-times (= time taken to send two characters at the programmed baud rate)
after the receive FIFO crosses the programmed trigger level (for all trigger tables A-D). To clear this condition,
the L212 will transmit the programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger
level below the programmed trigger level (for Trigger Tables A, B, and C) or when receive FIFO is less than the
trigger level minus the hysteresis value (for Trigger Table D). This hysteresis value is the same as the Auto
RTS Hysteresis value in Table 13. Table 6 below explains this when Trigger Table-B (See Table 14) is
selected.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2 characters);
for example, after 2.083ms has elapsed for 9600 baud and 8-bit word length, no parity and 1 stop bit setting.
2.17
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The L212 compares each incoming receive character with the programmed Xoff-2 data. If a match exists, the
received data will be transferred to the RX FIFO and ISR bit-4 will be set to indicate detection of special
character. Although the Internal Register Table shows Xon, Xoff Registers with eight bits of character
information, the actual number of bits is dependent on the programmed word length. Line Control Register
(LCR) bits 0-1 define the number of character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length
selected by LCR bits 0-1 also determines the number of bits that will be used for the special character
comparison. Bit-0 in the Xon, Xoff Registers corresponds with the LSB bit for the receive character.
TABLE 6: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
28
28*
24
相關PDF資料 |
PDF描述 |
|---|---|
| VI-25M-EX | CONVERTER MOD DC/DC 10V 75W |
| A3BKB-1018G | IDC CABLE- ASR10B/AE10G/APK10B |
| VI-JVT-EZ-S | CONVERTER MOD DC/DC 6.5V 25W |
| UPJ1K470MPD6TD | CAP ALUM 47UF 80V 20% RADIAL |
| H3WWH-2406G | IDC CABLE - HPL24H/AE24G/HPL24H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L212IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L212IL48TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 5V 48-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR19L212IL48TR-F |
| XR19L220 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L220_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L220IL40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。