- 您現在的位置：買賣IC網 > PDF目錄16511 > XR19L400IL40-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L202 40QFN PDF資料下載
參數資料
| 型號： | XR19L400IL40-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 8/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR19L202 40QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR19L400
16
SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
REV. 1.0.3
2.12
Sleep Mode, ACP Mode and Power-Save Feature with Wake-Up Interrupt
2.12.1
UART sleep mode (3.3V or 5V operation)
The UART portion in the L400 can enter sleep mode if all of these conditions are satisfied:
■ no interrupts pending (ISR bit-0 = 1)
■ the 16-bit divisor programmed in DLM and DLL registers is a non-zero value
■ sleep mode is enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idle
The L400 stops its crystal oscillator to conserve power in this mode. The user can check the XTAL2 pin for no
clock output as an indication that the device has entered the partial sleep mode.
The UART portion in the L400 resumes normal operation or active mode by any of the following:
■ a receive data start bit transition on the RX inputs
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: i.e., any of the MSR bits 0-
3 shows a ’1’ (in internal loopback mode)
If the sleep mode is enabled and the L400 is awakened by one of the conditions described above, an interrupt
is issued by the L400 to signal to the CPU that it is awake. The lower nibble of the interrupt source register
(ISR) will read a value of 0x1 for this interrupt and reading the ISR clears this interrupt. Since the same value
(0x1) is also used to indicate no pending interrupt, users should exercise caution while using the sleep mode.
The UART portion in the L400 will return to the sleep mode automatically after all interrupting conditions have
been serviced and cleared. If the UART portion of the L400 is awakened by the modem inputs, a read to the
MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an interrupt
is pending. The UART portion of the L400 will stay in the sleep mode of operation until it is disabled by setting
IER bit-4 to a logic 0.
2.12.1.1
Receiving data in UART sleep mode
There is a start-up delay for the crystal oscillator after waking up from sleep mode, therefore the first few
receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. If an external oscillator is
used, any data received will be transferred to/from the UART without any issues.
2.12.2
UART active, Charge pump of RS-485 transceiver shut down (3.3V operation only)
If the ACP pin is HIGH and the UART portion of the L400 is not in sleep mode, then the charge pump will
automatically shut down to conserve power if the following conditions are true:
■ no activity on the TX output signals
■ modem inputs have been idle for approximately 30 seconds
When these conditions are satisfied, the L400 shuts down the charge pump and tri-states the RS-485 drivers
to conserve power. In this mode, the RS-485 receivers are fully active and the internal registers of the L400
can be accessed. The time for the charge pump to resume normal operation after exiting the sleep mode is
typically 45
s. It will wake up by any of the following:
■ a receive data start bit transition on the RX input (LOW to HIGH)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a LOW to HIGH transition on any of the modem or general purpose serial inputs
Because the receivers are fully active when the charge pump is turned off, any data received will be transferred
to/from the UART without any issues.
2.12.2.1
Transmitting data in ACP Mode
相關PDF資料 |
PDF描述 |
|---|---|
| UVZ2V010MED | CAP ALUM 1UF 350V 20% RADIAL |
| EB63-S1R106FS | CONN EDGEBOARD DUAL 20POS 3A |
| EBM10DRSD-S664 | CONN EDGECARD 20POS DIP .156 SLD |
| M2MXH-3420K | IDC CABLE - MDM34H/MC34F/X |
| 1-5503162-8 | CA SM DUAL 2.5MM/2.5MM 4.58M1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L400IL40-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L400IL40TR-F | 功能描述:UART 接口集成電路 Transceiver 1 Tx/1 Rx RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L402 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。