- 您現在的位置：買賣IC網 > PDF目錄16606 > XR20M1280L32-0A-EB (Exar Corporation)EVAL BOARD FOR XR20M1280L32 PDF資料下載
參數資料
| 型號： | XR20M1280L32-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 18/63頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR20M1280L32 |
| 產品培訓模塊： | XR21V141x Full-Speed USB UART Family UARTs with Integrated Level Shifters |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 已用 IC / 零件： | XR20M1280L32 |
| 已供物品： | 板 |
| 其它名稱： | 1016-1630 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
XR20M1280
25
REV. 1.0.0
I2C/SPI UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
1.20
Sleep Mode with Auto Wake-Up
The M1280 supports low voltage system designs, hence, a sleep mode with auto wake-up feature is included
to reduce its power consumption when the chip is not actively used.
1.20.1
Sleep mode - IER bit-4
All of these conditions must be satisfied for the M1280 to enter sleep mode:
■ no interrupts pending (ISR bit-0 = 1)
■ sleep mode is enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pin is idling HIGH in normal mode or LOW in infrared mode
■ divisor is non-zero
■ TX and RX FIFOs are empty
The M1280 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M1280 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M1280 is awakened by any one of the above conditions, it will return to the sleep mode automatically
after all interrupting conditions have been serviced and cleared. If the M1280 is awakened by the modem
inputs, a read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be
entered while an interrupt is pending from any channel. The M1280 will stay in the sleep mode of operation
until it is disabled by setting IER bit-4 to a logic 0.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX pin is idling HIGH or “marking” condition
during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or another
type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the system design
engineer can use a 47k ohm pull-up resistor on each of the RX input.
1.20.2
Sleep Mode - SLEEP pin
The M1280 has a new pin called the SLEEP pin that can be used instead of setting IER bit-4=1. The M1280
will enter the sleep mode when:
■ the current byte in the TSR has completely shifted out
■ the current byte in the RSR has been completely received
Under this condition, there could be data in the TX and RX FIFOs. Any data that is the TX and RX FIFOs when
the SLEEP pin is asserted will not be affected. The only data that will be lost is any data that is still being
received on the RX pin. The M1280 will only wake up after the SLEEP pin has been de-asserted.
1.20.3
Wake-up Interrupt
The M1280 has the wake up interrupt. By setting the FCR bit-3, wake up interrupt is enabled or disabled. The
default status of wake up interrupt is disabled. Please See ”Section 3.5, FIFO Control Register (FCR) -
相關PDF資料 |
PDF描述 |
|---|---|
| EEC05DRAI-S734 | CONN EDGECARD 10POS .100 R/A PCB |
| B82477R4362M100 | INDUCTOR POWER 3.6UH 8.05A SMD |
| GCC06DREH-S93 | CONN EDGECARD 12POS .100 EYELET |
| V150C12E150BL | CONVERTER MOD DC/DC 12V 150W |
| V150C12E150BG3 | CONVERTER MOD DC/DC 12V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20M1280L32-0B-EB | 功能描述:UART 接口集成電路 EVAL F/M1280 QFN32 SPI INTERFACE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1280L40-0A-EB | 功能描述:UART 接口集成電路 EVAL F/M1280 QFN40 I2C INTERFACE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1280L40-0B-EB | 功能描述:UART 接口集成電路 EVAL F/M1280 QFN40 SPI INTERFACE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20V2170 | 制造商:EXAR 制造商全稱:EXAR 功能描述:I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
| XR20V2170IL40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。