參數資料
| 型號： | XRT73LC04AIV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 35/64頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| 標準包裝： | 60 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規(guī)程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
XRT73LC04A
36
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.2
3.2
THE RECEIVE EQUALIZER BLOCK
The purpose of this block is to equalize the incoming
distorted signal due to cable loss. The Receive
Equalizer attempts to restore the shape of the line
signal so that the transmitted data and clock can be
recovered reliably.
.
3.2.1
Guidelines for Setting the Receive Equal-
izer
This data sheet presents guidelines for setting the
Receive Equalizer, for the following conditions.
1. If the overall cable length, from the local Receiv-
ing Terminal to the Remote Transmitting Terminal
is NOT known.
2. If the overall cable length, from the Local Receiv-
ing Terminal to the remote Transmitting Terminal
is known.
3.2.1.1
If the Overall Cable Length is NOT
Known
This section presents recommendations on what
state to set the Receive Equalizer when the overall
cable-length, from the local Receiving Terminal to the
remote Transmitting Terminal is NOT known. For
DS3, STS-1 and E3 applications, enable the Receive
Equalizer by setting either the REQEN_(n) input pin
“high” or the REQEN_(n) bit-field to “1”. The remain-
der of this section provides an explanation why we
recommend enabling the Receive Equalizer for these
applications.
3.2.1.1.1
The Use of the Receive Equalizer in a
Typical DS3 or STS-1 Application
Most System Manufacturers of equipment supporting
DS3 and STS-1 lines, interface their equipment to ei-
ther a DSX-3 or STSX-1 Cross-Connect. While in-
stalling their equipment the Transmit Line Build-Out
circuit is set to the proper setting that makes the
transmit output pulse compliant with the Isolated
DSX-3 or STSX-1 Pulse Template requirements. For
the XRT73LC04A, this is achieved by setting the
TXLEV_(n) input pin or bit-field to the appropriate lev-
el.
FIGURE 23. THE TYPICAL APPLICATION FOR THE SYSTEM INSTALLER
Digital Cross-Connect
System
Transmitting
Terminal
Receiving
Terminal
0 to 450 feet of Cable
Pulses that are
compliant to the
Isolated DSX-3 or
STSX-1 Pulse Template
Requirement
0 to 450 feet of
Cable
DSX-3
or
STSX-1
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75L00DIV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L02DIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73R06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73R06ES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發(fā)器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73R06IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73R06IB-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73R12 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
發(fā)布緊急采購，3分鐘左右您將得到回復。