參數資料
型號: XRT73LC04AIV-F
廠商: Exar Corporation
文件頁數: 51/64頁
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 4CH 144LQFP
標準包裝: 60
類型: 線路接口裝置(LIU)
驅動器/接收器數: 4/4
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 144-LQFP
供應商設備封裝: 144-LQFP(20x20)
包裝: 托盤
XRT73LC04A
51
REV. 1.0.2
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
When the Transmit Drive Monitor circuitry within a
given line is connected to the line, as illustrated in
Figure 36, then it monitors the line for transitions. As
long as the Transmit Drive Monitor circuitry detects
transitions on the line via the MTIP_(n) and
MRing_(n) pins, then it keeps the DMO (Drive Monitor
Output) signal "Low". If the Transmit Drive Monitor
circuit detects no transitions on the line for 128+32
TxClk periods, then the DMO (Drive Monitor Output)
signal toggles "High".
NOTE: The Transmit Drive Monitor circuit does not have to
be used to operate the Transmit Section of the
XRT73LC04A. This is purely a diagnostic feature.
4.6
THE TAOS (TRANSMIT ALL ONES) FEATURE
The XRT73LC04A can command any channel to
transmit an all “1’s" pattern onto the line by toggling a
single input pin or by setting a single bit-field within
one of the Command Registers to "1".
NOTE: When this feature is activated, the Transmit Section
of the configured channel overwrites the Terminal Equip-
ment data with this all “1’s" pattern.
a. Operating in the Hardware Mode
Configure Channel(n) to transmit an all “1’s" pattern
by toggling the TAOS_(n) input pin (pin 45, 46, 135 or
136) “High". Terminate the all “1’s" pattern by tog-
gling the TAOS_(n) input pin “Low".
b. Operating in the HOST Mode
Configure Channel(n) to transmit an all “1’s" pattern
by writing to Command Register CR1-(n) and setting
the TAOS_(n) bit-field (bit D3) to "1".
Terminate the all “1’s" pattern by writing to Command
Register CR1-(n) and setting the TAOS_(n) bit-field
(D3) to "0".
5.0
THE MICROPROCESSOR SERIAL INTER-
FACE
The on-chip Command Registers of XRT73LC04A
DS3/E3/STS-1 Line Interface Unit IC are used to con-
figure the XRT73LC04A into a wide-variety of modes.
This section discusses the following:
1. The description of the Command Registers.
2. A description on how to use the Microprocessor
Serial Interface.
5.1
DESCRIPTION OF THE COMMAND REGISTERS
(repeated as Table 7), lists the Command Registers,
their Addresses and their bit-formats.
FIGURE 36. THE XRT73LC04A EMPLOYING THE TRANSMIT DRIVE MONITOR FEATURES
R1 = 31.6
R2 = 31.6
Channel (n)
TxPOS_(n)
TxNEG_(n)
TxLineClk_(n)
TTIP_(n)
TRing_(n)
TPData_(n)
TNData_(n)
TxClk_(n)
Only One Channel Shown
1:1
J1
BNC
MTIP_(n)
MRing_(n)
R3 = 270
R4 = 270
COMMAND REGISTER CR1-(n)
D4
D3
D2
D1
D0
TxOFF_(n) TAOS_(n) TxClkINV_(n) TxLEV_(n) Reserved
0
1
X
相關PDF資料
PDF描述
XRT73R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT73R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75L00DIV-F IC LIU E3/DS3/STS-1 SGL 52TQFP
XRT75L00IV-F IC LIU E3/DS3/STS-1 SGL 52TQFP
XRT75L02DIV-F IC LIU E3/DS3/STS-1 2CH 100TQFP
相關代理商/技術參數
參數描述
XRT73R06 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R06ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73R06IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R06IB-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R12 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT