參數資料
型號： XRT75L06D
廠商： Exar Corporation
英文描述： SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： 六通道E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數： 20/103頁
文件大?。?/td> 679K
代理商： XRT75L06D
xr
REV. 1.0.4
XRT75L06D
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
16
1.0
CLOCK SYNTHESIZER
The LIU uses a flexible user interface for accepting clock references to generate the internal master clocks
used to drive the LIU. The reference clock used to supply the microprocessor timing is generated from the DS-
3 or SFM clock input. Therefore, if the chip is configured for STS-1 only or E3 only, then the DS-3 input pin
must be connected to the STS-1 pin or E3 pin respectively. In DS-3 mode or when SFM is used, the STS-1
and E3 input pins can be left unconnected. If SFM is enabled by pulling the SFM_EN pin "High", 12.288MHz is
the only clock reference necessary to generate DS-3, E3, or STS-1 line rates and the microprocessor timing.
A simplified block diagram of the clock synthesizer is shown in Figure 3
1.1
Network cards that are designed to support multiple line rates which are not configured for single frequency
mode should ensure that a clock is applied to the DS3Clk input pin. For example: If the network card being
supplied to an ISP requires E3 only, the DS-3 input clock reference is still necessary to provide read and write
access to the internal microprocessor. Therefore, the E3 mode requires two input clock references. If
however, multiple line rates will not be supported, i.e. E3 only, then the DS3Clk input pin may be hard wire
connected to the E3Clk input pin.
Clock Distribution
F
IGURE
4. C
LOCK
D
ISTRIBUTION
C
ONGIFURED
IN
E3 M
ODE
W
ITHOUT
U
SING
SFM
N
OTE
:
For one input clock reference, the single frequency mode should be used.
F
IGURE
3. S
IMPLIFIED
B
LOCK
D
IAGRAM
OF
THE
I
NPUT
C
LOCK
C
IRCUITRY
D
RIVING
THE
M
ICROPROCESSOR
Clock Synthesizer
μ
Processor
LOL_n
DS3Clk
SFM_EN
STS-1Clk/12M
E3Clk
CLKOUT_n
0
1
Clock Synthesizer
μ
Processor
LOL_n
DS3Clk
E3Clk
CLKOUT_n
相關PDF資料
PDF描述
XRT75L06DIB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75L06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03DIV THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
相關代理商/技術參數
參數描述
XRT75L06DES 功能描述:時鐘合成器/抖動清除器 6CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L06DIB 功能描述:接口 - 專用 6CH E3/DS3/STS1 LIU w/DeSynch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT75L06DIB-F 功能描述:外圍驅動器與原件 - PCI 6-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L06ES 功能描述:時鐘合成器/抖動清除器 6 CHT3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L06IB 功能描述:接口 - 專用 6CH E3/DS3/STS1 LIU+Jitter Attenuato RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*