參數資料
型號： XRT75L06D
廠商： Exar Corporation
英文描述： SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： 六通道E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數： 38/103頁
文件大?。?/td> 679K
代理商： XRT75L06D
XRT75L06D
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
xr
REV. 1.0.4
34
4.0
There are three fundamental parameters that describe circuit performance relative to jitter
Jitter Tolerance
Jitter Transfer
Jitter Generation
4.1
J
ITTER
T
OLERANCE
Jitter tolerance is a measure of how well a Clock and Data Recovery unit can successfully recover data in the
presence of various forms of jitter. It is characterized by the amount of jitter required to produce a specified bit
error rate. The tolerance depends on the frequency content of the jitter. Jitter Tolerance is measured as the
jitter amplitude over a jitter spectrum for which the clock and data recovery unit achieves a specified bit error
rate (BER). To measure the jitter tolerance as shown in Figure 25, jitter is introduced by the sinusoidal
modulation of the serial data bit sequence. Input jitter tolerance requirements are specified in terms of
compliance with jitter mask which is represented as a combination of points. Each point corresponds to a
minimum amplitude of sinusoidal jitter at a given jitter frequency.
JITTER
4.1.1
Bellcore GR-499 CORE specifies the minimum requirement of jitter tolerance for Category I and Category II.
The jitter tolerance requirement for Category II is the most stringent. Figure 26 shows the jitter tolerance curve
as per GR-499 specification.
DS3/STS-1 Jitter Tolerance Requirements
F
IGURE
25. J
ITTER
T
OLERANCE
M
EASUREMENTS
FREQ
Synthesizer
Pattern
Generator
DUT
XRT75L06D
Error
Detector
Modulation
Freq.
Data
Clock
相關PDF資料
PDF描述
XRT75L06DIB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75L06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03DIV THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
相關代理商/技術參數
參數描述
XRT75L06DES 功能描述:時鐘合成器/抖動清除器 6CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L06DIB 功能描述:接口 - 專用 6CH E3/DS3/STS1 LIU w/DeSynch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT75L06DIB-F 功能描述:外圍驅動器與原件 - PCI 6-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L06ES 功能描述:時鐘合成器/抖動清除器 6 CHT3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L06IB 功能描述:接口 - 專用 6CH E3/DS3/STS1 LIU+Jitter Attenuato RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*