參數資料
型號: XRT75L06DIB
廠商: EXAR CORP
元件分類: 數字傳輸電路
英文描述: SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述: DATACOM, PCM TRANSCEIVER, PBGA217
封裝: 23 X 23 MM, BGA-217
文件頁數: 47/103頁
文件大小: 679K
代理商: XRT75L06DIB
xr
REV. 1.0.4
XRT75L06D
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
43
6.1
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are de-
scribed below in
Table 12
. The microprocessor interface can be configured to operate in Asynchronous mode
or Synchronous mode.
T
HE
M
ICROPROCESSOR
I
NTERFACE
B
LOCK
S
IGNALS
T
ABLE
12: XRT75L06D M
ICROPROCESSOR
I
NTERFACE
S
IGNALS
P
IN
N
AME
T
YPE
D
ESCRIPTION
Pmode
I
Microprocessor Interface Mode Select Input pin
This pin is used to specify the microprocessor interface mode.
D[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
Addr[7:0]
I
Eight-Bit Address Bus Inputs
The XRT75L06D LIU microprocessor interface uses a direct address bus. This address bus is
provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT75L06D LIU and
enables Read/Write operations with the on-chip register locations.
RD
I
Read Signal
This active low input functions as the read signal from the local
μ
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read operation has been
requested and begins the process of the read cycle.
WR
I
Write Signal
This active low input functions as the write signal from the local
μ
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write operation has been
requested and begins the process of the write cycle.
RDY
O
Ready Output
This active low signal is provided by the LIU device. It indicates that the cur-
rent read or write cycle is complete, and the LIU is waiting for the next command.
INT
O
Interrupt Output
This active low signal is provided by the LIU to alert the local mP that a
change in alarm status has occured. This pin is Reset Upon Read (RUR) once the alarm sta-
tus registers have been cleared.
RESET
I
Reset Input
This active low input pin is used to Reset the LIU.
相關PDF資料
PDF描述
XRT75L06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75L06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03DIV THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03 THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75L06DIB-F 功能描述:外圍驅動器與原件 - PCI 6-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L06ES 功能描述:時鐘合成器/抖動清除器 6 CHT3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L06IB 功能描述:接口 - 專用 6CH E3/DS3/STS1 LIU+Jitter Attenuato RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT75L06IB-F 功能描述:外圍驅動器與原件 - PCI 6-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R03 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR