參數資料
型號： XRT75R06IB
廠商： EXAR CORP
元件分類： 數字傳輸電路
英文描述： SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
中文描述： DATACOM, PCM TRANSCEIVER, PBGA217
封裝： 23 X 23 MM, BGA-217
文件頁數： 47/63頁
文件大小： 350K
代理商： XRT75R06IB
á
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R06
REV. 1.0.0
44
7.1
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are de-
scribed below in Table 12. The microprocessor interface can be configured to operate in Asynchronous mode
or Synchronous mode.
T
HE
M
ICROPROCESSOR
I
NTERFACE
B
LOCK
S
IGNALS
T
ABLE
12: XRT75R06 M
ICROPROCESSOR
I
NTERFACE
S
IGNALS
P
IN
N
AME
T
YPE
D
ESCRIPTION
Pmode
I
Microprocessor Interface Mode Select Input pin
This pin is used to specify the microprocessor interface mode.
D[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
Addr[7:0]
I
Eight-Bit Address Bus Inputs
The XRT75R06 LIU microprocessor interface uses a direct address bus. This address bus is
provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT75R06 LIU and enables
Read/Write operations with the on-chip register locations.
RD
I
Read Signal
This active low input functions as the read signal from the local
μ
P When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read operation has been
requested and begins the process of the read cycle.
WR
I
Write Signal
This active low input functions as the write signal from the local
μ
P When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write operation has been
requested and begins the process of the write cycle.
RDY
O
Ready Output
This active low signal is provided by the LIU device. It indicates that the current
read or write cycle is complete, and the LIU is waiting for the next command.
INT
O
Interrupt Output
This active low signal is provided by the LIU to alert the local mP that a
change in alarm status has occured. This pin is Reset Upon Read (RUR) once the alarm sta-
tus registers have been cleared.
RESET
I
Reset Input
This active low input pin is used to Reset the LIU.
相關PDF資料
PDF描述
XRT75R12D TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R12DIB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R12 TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R12IB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00 E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75R06IB208 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Parallel 217-Pin BGA
XRT75R06IB-F 功能描述:外圍驅動器與原件 - PCI 6 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R12 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75R12_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75R12_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*