參數資料
型號： XRT83SL314IB
廠商： Exar Corporation
文件頁數： 38/83頁
文件大?。?/td> 0K
描述： IC LIU SH T1/E1/J1 14CH 304TBGA
標準包裝： 27
類型： 線路接口裝置（LIU）
驅動器/接收器數： 14/14
規程： T1，E1，J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 304-LBGA
供應商設備封裝： 304-TBGA（31x31）
包裝： 托盤
xr
XRT83SL314
14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.1
40
4.6.1
T1 Short Haul Line Build Out (LBO)
The short haul transmitter output pulses are generated using a 7-Bit internal DAC (6-Bit plus the MSB sign bit).
The line build out can be set to interface to five different ranges of cable attenuation by programming the
appropriate channel register. The pulse shape is divided into eight discrete time segments which are set to
fixed values to comply with the pulse template. To program the eight segments individually to optimize a
special line build out, see the arbitrary pulse section of this datasheet. The short haul LBO settings are shown
4.6.2
Arbitrary Pulse Generator For T1 and E1
The arbitrary pulse generator divides the pulse into eight individual segments. Each segment is set by a 7-Bit
binary word by programming the appropriate channel register. This allows the system designer to set the
overshoot, amplitude, and undershoot for a unique line build out. The MSB (bit 7) is a sign-bit. If the sign-bit is
set to "0", the segment will move in a positive direction relative to a flat line (zero) condition. If this sign-bit is
set to "1", the segment will move in a negative direction relative to a flat line condition. The resolution of the
DAC is typically 60mV per LSB. Thus, writing 7-bit = 1111111 will clamp the output at either voltage rail
corresponding to a maximum amplitude. A pulse with numbered segments is shown in Figure 36.
FIGURE 36. ARBITRARY PULSE SEGMENT ASSIGNMENT
NOTE: By default, the arbitrary segments are programmed to 0x00h. The transmitter outputs will result in an all zero
pattern to the line interface.
4.7
DMO (Digital Monitor Output)
The driver monitor circuit is used to detect transmit driver failures by monitoring the activities at TTIP/TRING
outputs. Driver failure may be caused by a short circuit in the primary transformer or system problems at the
transmit inputs. If the transmitter of a channel has no output for more than 128 clock cycles, DMO goes "High"
until a valid transmit pulse is detected. If the DMO interrupt is enabled, the change in status of DMO will cause
TABLE 13: SHORT HAUL LINE BUILD OUT
LBO SETTING EQC[4:0]
RANGE OF CABLE ATTENUATION
08h (01000)
0 - 133 Feet
09h (01001)
133 - 266 Feet
0Ah (01010)
266 - 399 Feet
0Bh (01011)
399 - 533 Feet
0Ch (01100)
533 - 655 Feet
1
2
3
4
5
6
7
8
Segment
Register
1
0xn8
2
0xn9
3
0xna
4
0xnb
5
0xnc
6
0xnd
7
0xne
8
0xnf
相關PDF資料
PDF描述
MS3101R22-23P CONN RCPT 8POS PANEL MNT W/PINS
XRT75L03IVTR-F IC LIU E3/DS3/STS-1 3CH 128LQFP
IDT72V3650L6BB8 IC FIFO SS 2048X36 6NS 144-BGA
MS3101A22-19P CONN RCPT 14POS FREE HNG W/PINS
ISL267440IUZ-T IC INTERFACE
相關代理商/技術參數
參數描述
XRT83SL314IB-F 功能描述:LIN 收發器 RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8
XRT83SL314IB-L 功能描述:LIN 收發器 14 channel, SH T1/E1 LIU RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8
XRT83SL34 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL34ES 功能描述:外圍驅動器與原件 - PCI 4 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SL34IV 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*