- 您現在的位置：買賣IC網 > PDF目錄9995 > XRT83SL314IB (Exar Corporation)IC LIU SH T1/E1/J1 14CH 304TBGA PDF資料下載
參數資料
| 型號： | XRT83SL314IB |
| 廠商： | Exar Corporation |
| 文件頁數： | 43/83頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU SH T1/E1/J1 14CH 304TBGA |
| 標準包裝： | 27 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 14/14 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 304-LBGA |
| 供應商設備封裝： | 304-TBGA（31x31） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
XRT83SL314
xr
REV. 1.0.1
14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
45
5.2
Intel Mode Programmed I/O Access (Asynchronous)
If the LIU is interfaced to an Intel type P, then it should be configured to operate in the Intel mode. Intel type
Read and Write operations are described below.
Intel Mode Read Cycle
Whenever an Intel-type P wishes to read the contents of a register, it should do the following.
1. Place the address of the target register on the address bus input pins ADDR[10:0].
2. While the P is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables further communication between the
P and the LIU microprocessor interface block.
3. Toggle the ALE input pin "High". This step enables the address bus input drivers, within the microproces-
sor interface block of the LIU.
4. The P should then toggle the ALE pin "Low". This step causes the LIU to latch the contents of the address
bus into its internal circuitry. At this point, the address of the register has now been selected.
5. Next, the P should indicate that this current bus cycle is a Read operation by toggling the RD input pin
"Low". This action also enables the bi-directional data bus output drivers of the LIU.
6. After the P toggles the Read signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
in order to inform the P that the data is available to be read by the P, and that it is ready for the next com-
mand.
7. After the P detects the RDY signal and has read the data, it can terminate the Read Cycle by toggling the
RD input pin "High".
NOTE: ALE can be tied “High” if this signal is not available.
The Intel Mode Write Cycle
Whenever an Intel type P wishes to write a byte or word of data into a register within the LIU, it should do the
following.
1. Place the address of the target register on the address bus input pins ADDR[10:0].
2. While the P is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables further communication between the
P and the LIU microprocessor interface block.
3. Toggle the ALE input pin "High". This step enables the address bus input drivers, within the microproces-
sor interface block of the LIU.
4. The P should then toggle the ALE pin "Low". This step causes the LIU to latch the contents of the address
bus into its internal circuitry. At this point, the address of the register has now been selected.
5. The P should then place the byte or word that it intends to write into the target register, on the bi-direc-
tional data bus DATA[7:0].
6. Next, the P should indicate that this current bus cycle is a Write operation by toggling the WR input pin
"Low". This action also enables the bi-directional data bus input drivers of the LIU.
7. After the P toggles the Write signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
in order to inform the P that the data has been written into the internal register location, and that it is ready
for the next command.
NOTE: ALE can be tied “High” if this signal is not available.
The Intel Read and Write timing diagram is shown in Figure 39.
The timing specifications are shown in
相關PDF資料 |
PDF描述 |
|---|---|
| MS3101R22-23P | CONN RCPT 8POS PANEL MNT W/PINS |
| XRT75L03IVTR-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| IDT72V3650L6BB8 | IC FIFO SS 2048X36 6NS 144-BGA |
| MS3101A22-19P | CONN RCPT 14POS FREE HNG W/PINS |
| ISL267440IUZ-T | IC INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL314IB-F | 功能描述:LIN 收發器 RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT83SL314IB-L | 功能描述:LIN 收發器 14 channel, SH T1/E1 LIU RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT83SL34 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL34ES | 功能描述:外圍驅動器與原件 - PCI 4 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL34IV | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。