參數資料
型號： Z86C46
廠商： ZiLOG, Inc.
英文描述： CMOS Z8 MCU(CMOS Z8系列微控制器)
中文描述： 單片機的CMOS Z8的CMOS（Z8系列微控制器）
文件頁數： 38/70頁
文件大?。?/td> 1192K
代理商： Z86C46
Z86C34/C35/C36/C44/C45/C46
CMOS Z8 MCUs with ASCI UART
ZiLOG
38
P R E L I M I N A R Y
DS007601-Z8X0499
FUNCTIONAL DESCRIPTION
(Continued)
0, 1, 2, and 3, and low-EMI oscillator. The
PCON
register
is located in the expanded register file at Bank F, location
00h
(Figure 25).
Comparator Output Port 3 (D0).
Bit
0
controls the com-
parator use in Port 3. A
1
in this location brings the com-
parator outputs to
P34
and
P37
, and a
0
releases the Port to
its standard I/O configuration. The default value is
0
.
Port 1 Open-Drain (D1).
Port 1 can be configured as an
open-drain by resetting this bit (
D1 = 0
) or configured as
push-pull active by setting this bit (
D1 = 1
). The default val-
ue is
1
. The user must set
D1 = 1
for devices in 28-pin pack-
ages.
Port 0 Open-Drain (D2).
Port 0 can be configured as an
open-drain by resetting this bit (
D2 = 0
) or configured as
push-pull active by setting this bit (
D2 = 1
). The default val-
ue is
1
.
Low-EMI Port 0 (D3).
Port 0 can be configured as a low-
EMI port by resetting this bit (
D3 = 0
) or configured as a
Standard Port by setting this bit (
D3 = 1
). The default value
is
1
.
Low-EMI Port 1 (D4).
Port 1 can be configured as a low-
EMI port by resetting this bit (
D4 = 0
) or configured as a
Standard Port by setting this bit (
D4 = 1
). The default value
is
1
. The user must set
D4 = 1
for devices in 28-pin packages.
Note:
For emulator, this bit must be set to
1
.
Low-EMI Port 2 (D5).
Port 2 can be configured as a low-
EMI port by resetting this bit (
D5 = 0
) or configured as a
Standard Port by setting this bit (
D5 = 1
). The default value
is
1
.
Low-EMI Port 3 (D6).
Port 3 can be configured as a low-
EMI port by resetting this bit (
D6 = 0
) or configured as a
Standard Port by setting this bit (
D6 = 1
). The default value
is
1
.
Low-EMI OSC (D7).
This bit of the
PCON
Register con-
trols the low-EMI noise oscillator. A
1
in this location con-
figures the oscillator,
DS
,
AS
and
R/W
with standard drive,
while a
0
configures the oscillator,
DS
,
AS
and
R/W
with
low noise drive. The low-EMI mode reduces the drive of
the oscillator (OSC). The default value is
1
.
Note:
Maximum external clock frequency of 4 MHz when run-
ning in the
low-EMI
oscillator mode.
Low-EMI Emission.
The Z8 can be programmed to operate
in a low-EMI emission mode in the
PCON
register. The os-
cillator and all I/O ports can be programmed as low-EMI
emission mode independently. Use of this feature results in:
The pre-drivers slew rate reduced to 10 ns (typical)
Low-EMI output drivers exhibit resistance of 200 Ohms
(typical)
Low-EMI Oscillator
Internal
SCLK/TCLK = XTAL
operation limited to a
maximum of 4 MHz–250 ns cycle time, when
LOW
EMI OSCILLATOR
is selected and system clock (
SCLK
= XTAL
,
SMR REGISTER BIT D1 = 1
)
Stop-Mode Recovery Register (SMR).
This register se-
lects the clock divide value and determines the mode of
Stop-Mode Recovery (Figures 26 and 27). All bits are
WRITE ONLY
, except bit
7
, which is
READ
ONLY
. Bit
7
is a flag bit that is hardware set on the condition of
STOP
recovery and
RESET
by a power-on cycle. Bit
6
controls
whether a low level or a high level is required from the re-
covery source. Bit
5
controls the reset delay after recovery.
Bits 2, 3, and 4, or the
SMR
register, specify the source of
the Stop-Mode Recovery signal. Bits
0
and
1
determine the
time-out period of the
WDT
. The
SMR
is located in Bank
F of the Expanded Register Group at address
0BH
.
Figure 25. Port Configuration Register (PCON)
(WRITE ONLY)
0 Port 0 Open Drain
1 Port 0 Push-pull Active*
D7
D6
D5
D4
D3
D2
D1
D0
PCON (FH) 00H
Comparator Output Port 3
0 P34, P37 Standard Output*
1 P34, P37 Comparator Output
0 Port 0 Low EMI
1 Port 0 Standard*
0 Port 2 Low EMI
1 Port 2 Standard*
Low EMI Oscillator
0 Low EMI
1 Standard*
0 Port 3 Low EMI
1 Port 3 Standard*
*Default Setting After Reset
Must be set to one for devices
in 28-pin packages
0 Port 1 Open Drain
1 Port 1 Push-pull Active*
0 Port 1 Low EMI
1
Port 1
Standard*
相關PDF資料
PDF描述
Z86C40 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C30 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C31 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C32 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C47 CMOS Z8 MICROCONTROLLER
相關代理商/技術參數
參數描述
Z86C47 制造商:ZILOG 制造商全稱:ZILOG 功能描述:CMOS Z8 MICROCONTROLLER
Z86C4704PSC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
Z86C5000ZEM 功能描述:仿真器/模擬器 Z8 In-Circuit Em-C50 RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
Z86C50-20GSE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
Z86C50-20VSC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*