參數資料
型號： ZL30102QDG
廠商： ZARLINK SEMICONDUCTOR INC
元件分類： 通信及網絡
英文描述： T1/E1 Stratum 4/4E Redundant System Clock Synchronizer for DS1/E1 and H.110
中文描述： SPECIALTY TELECOM CIRCUIT, PQFP64
封裝： 10 X 10 MM, 1 MM HEIGHT, MS-026ACD, TQFP-64
文件頁數： 9/50頁
文件大?。?/td> 481K
代理商： ZL30102QDG
ZL30102
Data Sheet
9
Zarlink Semiconductor Inc.
2.2 Pin Description
Pin #
Name
Description
1
GND
Ground.
0 V
2
V
CORE
LOCK
Positive Supply Voltage.
+1.8 V
DC
nominal
Lock Indicator (Output).
This output goes to a logic high when the PLL is frequency
locked to the selected input reference.
3
4
HOLDOVER
Holdover (Output).
This output goes to a logic high whenever the PLL goes into
holdover mode.
5
REF_FAIL0
Reference 0 Failure Indicator (Output).
A logic high at this pin indicates that the REF0
reference frequency has exceeded the out-of-range limit set by the OOR_SEL pin or that
it is exhibiting abrupt phase or frequency changes.
6
REF_FAIL1
Reference 1 Failure Indicator (Output).
A logic high at this pin indicates that the REF1
reference frequency has exceeded the out-of-range limit set by the OOR_SEL pin or that
it is exhibiting abrupt phase or frequency changes.
7
REF_FAIL2
Reference 2 Failure Indicator (Output).
A logic high at this pin indicates that the REF2
reference frequency has exceeded the out-of-range limit set by the OOR_SEL pin or that
it is exhibiting abrupt phase or frequency changes.
8
TDO
Test Serial Data Out (Output).
JTAG serial data is output on this pin on the falling edge
of TCK. This pin is held in high impedance state when JTAG scan is not enabled.
9
TMS
Test Mode Select (Input).
JTAG signal that controls the state transitions of the TAP
controller. This pin is internally pulled up to V
DD
. If this pin is not used then it should be
left unconnected.
10
TRST
Test Reset (Input).
Asynchronously initializes the JTAG TAP controller by putting it in
the Test-Logic-Reset state. This pin should be pulsed low on power-up to ensure that
the device is in the normal functional state. This pin is internally pulled up to V
DD
. If
this pin is not used then it should be connected to GND.
11
TCK
Test Clock (Input):
Provides the clock to the JTAG test logic. If this pin is not used then it
should be pulled down to GND.
12
V
CORE
GND
Positive Supply Voltage.
+1.8 V
DC
nominal
Ground.
0 V
13
14
AV
CORE
TDI
Positive Analog Supply Voltage.
+1.8 V
DC
nominal
Test Serial Data In (Input).
JTAG serial test instructions and data are shifted in on this
pin. This pin is internally pulled up to V
DD
. If this pin is not used then it should be left
unconnected.
15
16
HMS
Hitless Mode Switching (Input).
The HMS input controls phase accumulation during the
transition from Holdover or Freerun mode to Normal mode on the same reference. A logic
low at this pin will cause the ZL30102 to maintain the delay stored in the TIE corrector
circuit when it transitions from Holdover or Freerun mode to Normal mode. A logic high
on this pin will cause the ZL30102 to measure a new delay for its TIE corrector circuit
thereby minimizing the output phase movement when it transitions from Holdover or
Freerun mode to Normal mode.
17
MODE_SEL0
Mode Select 0 (Input).
This input combined with MODE_SEL1 determines the mode of
operation, see Table 4 on page 22.
18
MODE_SEL1
Mode Select 1 (Input).
See MODE_SEL0 pin description.
相關PDF資料
PDF描述
ZL30105QDG1 T1/E1/SDH Stratum 3 Redundant System Clock Synchronizer for AdvancedTC TM and H.110
ZL30105 Power Clamp On Multimeter; DMM Type:Clamp; No. of Digits/Alpha:3-3/4; DMM Response Type:True RMS; Approval Categories:CAT III 600V; Calibrated:No; Current Measuring Range:0-400.0A; Current Setting AC:400A RoHS Compliant: NA
ZL30105QDG Digital Clamp-On Meter; DMM Type:Clamp; No. of Digits/Alpha:3-3/4; DMM Response Type:True RMS; Calibrated:No; Current Setting AC:1000A; Resistance Measuring Range:400 Ohm to 10 MOhm; Voltage Measuring Range AC:600V RoHS Compliant: NA
ZL30106QDG1 SONET/SDH/PDH Network Interface DPLL
ZL30106 SONET/SDH/PDH Network Interface DPLL
相關代理商/技術參數
參數描述
ZL30102QDG1 制造商:Microsemi Corporation 功能描述:PB FREE T1/E1 SYSTEM SYNCHRONIZER - Trays 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE T1/E1 SYSTEM SYNCHRONIZER - Trays
ZL30105 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/SDH Stratum 3 Redundant System Clock Synchonizer for AdvancedTCA and H.110
ZL30105_05 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/SDH Stratum 3 Redundant System Clock Synchronizer for AdvancedTC TM and H.110
ZL30105QDG 制造商:Zarlink Semiconductor Inc 功能描述:CLOCK SYNTHESIZER 64TQFP - Bulk
ZL30105QDG1 制造商:Microsemi Corporation 功能描述:CLOCK SYNTHESIZER 64TQFP - Trays 制造商:Microsemi Corporation 功能描述:IC Pb Free T1/E1 System Synchronizer 制造商:Zarlink Semiconductor Inc 功能描述:CLOCK SYNTHESIZER 64TQFP - Trays 制造商:Zarlink Semiconductor Inc 功能描述:IC Pb Free T1/E1 System Synchronizer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*