參數資料
型號： 1200
廠商： TEXAS INSTRUMENTS INC
元件分類： 無繩電話/電話
英文描述： TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC20
封裝： 4 X 4 MM, ROHS COMPLIANT, QLP-20
文件頁數： 6/70頁
文件大?。?/td> 841K
代理商： 1200
Chipcon
SmartRF CC1100
Chipcon AS
SmartRF
CC1100 Preliminary Data Sheet (rev. 1.0) 2005-04-25
Page 14 of 68
14 Circuit Description
BIAS
PA
RBIAS
XOSC_Q1
XOSC_Q2
CSn
SI
SO (GDO1)
XOSC
SCLK
LNA
0
90
FREQ
SYNTH
ADC
DE
MO
DULATO
R
F
E
C
/
IN
T
E
R
L
E
A
V
E
R
PACKET
HANDLER
RX
FIF
O
MO
DULATO
R
TX
FIF
O
DI
GI
TAL
I
N
T
E
RFACE
TO
MCU
RADIO CONTROL
RF_P
RF_N
GDO2
GDO0 (ATEST)
RC OSC
Figure 2:
CC1100 Simplified Block Diagram
A simplified block diagram of
CC1100 is shown
CC1100
features a low-IF receiver. The
received RF signal is amplified by the low-
noise amplifier (LNA) and down-converted in
quadrature (I and Q) to the intermediate
frequency (IF). At IF, the I/Q signals are
digitised by the ADCs. Automatic gain control
(AGC), fine channel filtering, demodulation
bit/packet
synchronization
is
performed
digitally.
The transmitter part of
CC1100 is based on
direct synthesis of the RF frequency. The
frequency synthesizer includes a completely
on-chip LC VCO and a 90 degree phase
shifter for generating the I and Q LO signals to
the down-conversion mixers in receive mode.
A crystal is to be connected to XOSC_Q1 and
XOSC_Q2. The crystal oscillator generates the
reference frequency for the synthesizer, as
well as clocks for the ADC and the digital part.
A 4-wire SPI serial interface is used for
configuration and data buffer access.
The digital baseband includes support for
channel configuration, packet handling and
data buffering.
15 Application Circuit
Only a few external components are required
for using the
CC1100. The recommended
application circuit is shown in Figure 3. The
external components are described in Table
14, and typical values are given in Table 15.
Bias resistor
The bias resistor R171 is used to set an
accurate bias current.
Balun and RF matching
C131, C121, L121 and L131 form a balun that
converts the differential RF port on
CC1100 to a
single-ended RF signal (C124 is also needed
for DC blocking). Together with an appropriate
LC network, the balun components also
transform the impedance to match a 50
antenna (or cable). Component values for the
RF balun and LC network are easily found
using
the
SmartRF
Studio
software.
Suggested values for 315MHz, 433MHz and
868/915MHz are listed in Table 15.
相關PDF資料
PDF描述
1200 TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT
1203CLUXE7/1NF PUSHBUTTON SWITCH, SPST, MOMENTARY, 3A, 12VDC, PANEL MOUNT-THREADED
1223ALUXE2UL-CSA PUSHBUTTON SWITCH, SPST, MOMENTARY, 8A, 12VDC, PANEL MOUNT-THREADED
1203ALUXE6UL-CSA PUSHBUTTON SWITCH, SPST, MOMENTARY, 8A, 12VDC, PANEL MOUNT-THREADED
1203CLUXE6NF PUSHBUTTON SWITCH, SPST, MOMENTARY, 3A, 12VDC, PANEL MOUNT-THREADED
相關代理商/技術參數
參數描述
1200 (4"X100FT) 制造商:3M Electronic Products Division 功能描述:TAPE, INSULATION, VINYL, BLACK 4INX100FT, Tape Type:Electrical Insulation, Tape
12000 制造商:Carclo Technical Plastics 功能描述:50MM TRIPLE HOLDER
120-00 制造商:HITEC 功能描述:DEPTH GAUGE VERNIER 制造商:HITEC 功能描述:DEPTH GAUGE, VERNIER
1200-0.3 制造商:VIDEK 功能描述:LEAD BNC PLG-PLG 0.3M 制造商:VIDEK 功能描述:LEAD, BNC PLG-PLG, 0.3M 制造商:VIDEK 功能描述:COAXIAL CABLE, RG-58, 0.3M, BLACK; Coaxial Cable Type:RG58; Cable Length - Imperial:11.81"; Cable Length - Metric:300mm; Connector Type A:BNC Straight Plug; Connector Type B:BNC Straight Plug; Jacket Color:Beige ;RoHS Compliant: Yes
120000 功能描述:環境檢測設備 PH METER ECONOMY RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*