參數資料
型號： 20-101-0358
廠商： Rabbit Semiconductor
文件頁數： 28/94頁
文件大小： 0K
描述： COMPUTER SINGLE-BOARD BL1820
標準包裝： 1
系列： Jackrabbit
模塊/板類型： 單板計算機模塊
適用于相關產品： BL1820
產品目錄頁面： 618 (CN2011-ZH PDF)
其它名稱： 316-1081
30
Jackrabbit (BL1800)
The Jackrabbit comes with a 220
termination resistor and 681 bias resistors already
installed, as shown in Figure 12.
Figure 12. RS-485 Termination and Bias Resistors
The load these bias and termination resistors present to the RS-485 transceiver (U6) limits
the number of Jackrabbits in a multidrop network to one master and nine slaves, unless the
bias and termination resistors are removed. When using more than 10 Jackrabbits in a
multidrop network, leave the 681
bias resistors in place on the master Jackrabbit, and
leave the 220
termination resistors in place on the Jackrabbit at each end of the network.
3.5.3 Programming Port
The Jackrabbit has a 10-pin program header labeled J3. The programming port uses the
Rabbit 2000’s Serial Port A for communication. Dynamic C uses the programming port to
download and debug programs.
The programming port is also used for the following operations.
Cold-boot the Rabbit 2000 after a reset.
Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Alternate Uses of the Serial Programming Port
All three clocked Serial Port A signals are available as
a synchronous serial port
an asynchronous serial port, with the clock line usable as a general CMOS input
The serial programming port may also be used as a serial port via the DIAG connector on
the serial programming cable.
U6
R18
681 W
R17
220 W
R16
681 W
485+
485
6
7
R16
termination
bias
R17
R18
U4
VIN
GND
RESET
JACKRABBIT Z-World, Inc.
GND
PA0
PA2
PA4
PA6
GND
PB0
PB2
PB4
PB6
WDO
GND
PE6
PE4
PE2
PE0
HV0
HV2
K
GND
VCC
PA1
PA3
PA5
PA7
GND
PB1
PB3
PB5
PB7
PCLK
PE7
PE5
PE3
PE1
GND
HV1
HV3
+RAW
VCC
GND
RXC
TXC
PC1
PC3
PC5
PC7
AGND
DA1
PD1
PD3
PD5
PD7
GND
485+
VCC
SM1
STAT
VBAT
GND
VCC
RXB
TXB
PC0
PC2
PC4
PC6
AD0
DA0
PD0
PD2
PD4
PD6
GND
485
VCC
SM0
IOBEN
GND
/RST
J5
U6
U5
U3
J4
U1
J1
J2
J3
Y3
Rabbit 2000
SRAM
RS-232
RS-485
相關PDF資料
PDF描述
20-101-0446 MODULE RABBITCORE RCM2130
AT25256-10PI-2.7 IC EEPROM 256KBIT 3MHZ 8DIP
345-030-524-801 CARDEDGE 30POS DUAL .100 GREEN
345-030-524-204 CARDEDGE 30POS DUAL .100 GREEN
345-030-524-202 CARDEDGE 30POS DUAL .100 GREEN
相關代理商/技術參數
參數描述
20-101-0383 功能描述:模塊化系統 - SOM RCM2020 RabbitCore RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0389 功能描述:子卡和OEM板 SR9200 16IN/8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0390 功能描述:子卡和OEM板 SR9210 8 in/ 16 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0391 功能描述:子卡和OEM板 SR9220 DIG I/O 8IN 8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0392 功能描述:子卡和OEM板 SR9300 A/D 0-10V RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*