參數資料
型號： 20-101-0494
廠商： Rabbit Semiconductor
文件頁數： 24/90頁
文件大小： 0K
描述： MODULE RABBITCORE RCM2250
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM2250
產品目錄頁面： 620 (CN2011-ZH PDF)
其它名稱： 316-1092
24
RabbitCore RCM2200
The RJ-45 connector is shielded to minimize EMI effects to/from the Ethernet signals.
Rabbit recommends that an equivalent RJ-45 connector be used on the user board if the
customer wishes to have an RJ-45 connector on the user board.
NOTE: The RCM2210 is available without the LEDs and the RJ-45 connector if you
plan to use your own RJ-45 connector on your user board.
4.2.3 Programming Port
The RCM2200 has a 10-pin program header labeled J1. The programming port uses the
Rabbit 2000’s Serial Port A for communication. Dynamic C uses the programming port to
download and debug programs.
The programming port is also used for the following operations.
Cold-boot the Rabbit 2000 after a reset.
Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Alternate Uses of the Serial Programming Port
All three clocked Serial Port A signals are available as
a synchronous serial port
an asynchronous serial port, with the clock line usable as a general CMOS input
The serial programming port may also be used as a serial port via the DIAG connector on
the serial programming cable.
In addition to Serial Port A, the Rabbit 2000 startup-mode (SMODE0, SMODE1), status,
and reset pins are available on the serial programming port.
The two startup mode pins determine what happens after a reset—the Rabbit 2000 is
either cold-booted or the program begins executing at address 0x0000. These two
SMODE pins can be used as general inputs once the cold boot is complete.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose CMOS output.
The /RESET_IN pin is an external input that is used to reset the Rabbit 2000 and the
onboard peripheral circuits on the RabbitCore module. The serial programming port can be
used to force a hard reset on the RabbitCore module by asserting the /RESET_IN signal.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information.
相關PDF資料
PDF描述
AT25020N-10SI-2.7 IC EEPROM 2KBIT 2.1MHZ 8SOIC
345-030-521-801 CARDEDGE 30POS DUAL .100 GREEN
12FMN-BMTTN-A-TF CONN FMN HSNG 12POS STAG NOR SMD
AT25020-10PI-2.7 IC EEPROM 2KBIT 2.1MHZ 8DIP
345-030-521-204 CARDEDGE 30POS DUAL .100 GREEN
相關代理商/技術參數
參數描述
20-101-0495 功能描述:處理器配件 BASEPLATE RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-0497 功能描述:單板計算機 OP6810 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
201-01050 功能描述:鋁質電解電容器 - 帶引線 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
201-0105-01 功能描述:印刷電路板和試驗板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度:
20-101-0502 功能描述:處理器配件 Keypad/Display Unit 5V Panle Mount RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*