- 您現在的位置：買賣IC網 > PDF目錄3913 > 20-101-0494 (Rabbit Semiconductor)MODULE RABBITCORE RCM2250 PDF資料下載
參數資料
| 型號： | 20-101-0494 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 5/90頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE RABBITCORE RCM2250 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2250 |
| 產品目錄頁面： | 620 (CN2011-ZH PDF) |
| 其它名稱： | 316-1092 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
User’s Manual
7
Although you can install a single module into either the MASTER or the SLAVE position
on the Prototyping Board, all the Prototyping Board features (switches, LEDs, serial port
drivers, etc.) are connected to the MASTER position. We recommend you install the mod-
ule in the MASTER position.
NOTE: It is important that you line up the pins on headers J4 and J5 of the RCM2200
exactly with the corresponding pins of header sockets J1 and J2 on the Prototyping
Board. The header pins may become bent or damaged if the pin alignment is offset, and
the module will not work. Permanent electrical damage to the module may also result if
a misaligned module is powered up.
Press the module’s pins firmly into the Prototyping Board header sockets.
2.1.2 Connect Programming Cable
The programming cable connects the RCM2200 module to the PC running Dynamic C to
download programs and to monitor the RCM2200 for debugging.
NOTE: COM 1 is the default port used by Dynamic C.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter (Part No. 20-151-0178) with the programming cable sup-
plied with the RCM2200 Development Kit. Note that not all RS-232/USB converters
work with Dynamic C.
Connect the 10-pin connector of the
programming cable labeled PROG
to header J1 on the RCM2200 mod-
ule as shown in Figure 2. Be sure to
orient the marked (usually red) edge
of the cable towards pin 1 of the
connector. (Do not use the DIAG
connector, which is used for a nor-
mal serial connection.)
Connect the other end of the pro-
gramming cable to a COM port on
your PC. Make a note of the port to
which you connect the cable, as
Dynamic C needs to have this
parameter configured when it is
installed.
Figure 2. Connect Programming Cable
to RCM2200
相關PDF資料 |
PDF描述 |
|---|---|
| AT25020N-10SI-2.7 | IC EEPROM 2KBIT 2.1MHZ 8SOIC |
| 345-030-521-801 | CARDEDGE 30POS DUAL .100 GREEN |
| 12FMN-BMTTN-A-TF | CONN FMN HSNG 12POS STAG NOR SMD |
| AT25020-10PI-2.7 | IC EEPROM 2KBIT 2.1MHZ 8DIP |
| 345-030-521-204 | CARDEDGE 30POS DUAL .100 GREEN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 20-101-0495 | 功能描述:處理器配件 BASEPLATE RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于: |
| 20-101-0497 | 功能描述:單板計算機 OP6810 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 201-01050 | 功能描述:鋁質電解電容器 - 帶引線 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
| 201-0105-01 | 功能描述:印刷電路板和試驗板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度: |
| 20-101-0502 | 功能描述:處理器配件 Keypad/Display Unit 5V Panle Mount RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于: |
發布緊急采購，3分鐘左右您將得到回復。