- 您現在的位置：買賣IC網 > PDF目錄370035 > 28233-11 (CONEXANT SYSTEMS) ATM Transmitter/Receiver with UTOPIA Interface PDF資料下載
參數資料
| 型號： | 28233-11 |
| 廠商： | CONEXANT SYSTEMS |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | ATM Transmitter/Receiver with UTOPIA Interface |
| 中文描述： | TRANSCEIVER, PQFP160 |
| 封裝： | PLASTIC, MQFP-160 |
| 文件頁數： | 78/161頁 |
| 文件大?。?/td> | 1832K |
| 代理商： | 28233-11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
the form
“
0xxxmmm011111111
”
. The right-most bit of this sequence is the first
bit transmitted on the channel. To initiate transmission of a message byte in the
FEAC channel, write the desired byte in the form
“
mmmxxx
”
into bits 15
–
10 of
the TXFEAC_ERRPAT register. A 1 must be written to Enable FEAC
Transmission [bit 9]. Transmission of the flag (11111111) and the 0s on either
side of the
“
xxxmmm
”
pattern is automatic. Ten repetitions of the message are
sent before an interrupt is issued on the DL_INT pin. The interrupt also appears
in the RXFEAC_VER register to request a new byte from the processor. To clear
the interrupt, you must write the TXFEAC_ERRPAT register. Each time a new
byte is written, 10 transmissions of that byte (and flag) will automatically occur.
Interrupts from the transmit FEAC channel will occur at a rate of approximately
one interrupt per 17 ms.
If you write a 0 to Enable FEAC Transmission [bit 9], then continuous
transmission of idle flags is enabled and no interrupts are issued until a byte of the
proper format is written to the TXFEAC_ERRPAT register. Interrupts from the
FEAC channel transmitter appear on Transmit FEAC Interrupt [bit 8] in the
RXFEAC_VER register [0x3C].
2.0 Functional Description
CN8223
2.8 FEAC Channel and HDLC Data Link Programming
ATM Transmitter/Receiver with UTOPIA Interface
2-44
Conexant
100046C
2.8 FEAC Channel and HDLC Data Link
Programming
This section discusses the use and programming requirements for the FEAC
channel and HDLC data link. The FEAC channel is used in DS3 mode; the
HDLC data link is used by DS3, E3, and STS-1/3 framers.
2.8.1 FEAC Channel Transmitter
The FEAC Channel transmitter is under control of the PHY Type [bits 2
–
0],
External Framer [bit 5] of CONFIG_1 [0x00], Transmit Alarm Control [bits 9
–
4
of CONFIG_2 [0x01], Enable FEAC Transmission [bit 9], and Transmit FEAC
Data [bits 15
–
10] of TXFEAC_ERRPAT [0x03]. An interrupt for use with FEAC
channel operations is available on the DL_INT output pin, and status bits for
determining the interrupt source are located in the RXFEAC_VER register
[0x3C].
The PHY type must be set to internal DS3 for FEAC channel transmission to
take place. In DS3 mode, the last C bit in subframe 1 of the M-frame is used for
transmission. Setting the Transmit Alarm Control [bits 9
–
4] for transmission of
AIS disables transmission of the FEAC channel. Transmission of yellow alarm or
idle code has no effect on FEAC channel transmission.
The TXFEAC_ERRPAT register controls the byte to be transmitted on the
FEAC channel. All messages for transmission on the FEAC channel must be in
相關PDF資料 |
PDF描述 |
|---|---|
| 28C010TRPDB-12 | 150 x 32 pixel format, LED Backlight available |
| 28C010TRT1DE-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1DE-20 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-20 | 1 Megabit (128K x 8-Bit) EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 282332-2 | 制造商:TE Connectivity 功能描述: |
| 282-333 | 制造商:WAGO Innovative Connections 功能描述:END PLATE RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO Innovative Connections 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK; Series:282; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks; Color:Orange; Mounting Type:DIN Rail ;RoHS Compliant: Yes |
| 2823337 | 功能描述:工業繼電器 ST-REL4-KG120/21-21 RoHS:否 制造商:TE Connectivity / Kilovac 觸點形式:1 Form A (SPST-NO) 觸點電流額定值: 線圈電壓:9 VDC to 36 VDC 線圈電阻:38 Ohms 線圈電流: 切換電壓: 安裝風格:Panel 觸點材料:Silver Palladium |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:End Plate 2 mm Thick-Color Grey For Use With Rail Mounted Terminal Block 制造商:WAGO 功能描述:GREY END PLATE 制造商:WAGO Innovative Connections 功能描述:END PLATE, 2MM, GREY; Series:-; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks ;RoHS Compliant: Yes |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:END PLATE 制造商:WAGO 功能描述:END PLATE |
發布緊急采購，3分鐘左右您將得到回復。