- 您現在的位置：買賣IC網 > PDF目錄370035 > 28233-11 (CONEXANT SYSTEMS) ATM Transmitter/Receiver with UTOPIA Interface PDF資料下載
參數資料
| 型號： | 28233-11 |
| 廠商： | CONEXANT SYSTEMS |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | ATM Transmitter/Receiver with UTOPIA Interface |
| 中文描述： | TRANSCEIVER, PQFP160 |
| 封裝： | PLASTIC, MQFP-160 |
| 文件頁數： | 83/161頁 |
| 文件大?。?/td> | 1832K |
| 代理商： | 28233-11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
RxBytes[2:0] = n
Bad FCS = 0 or 1
CN8223
2.0 Functional Description
ATM Transmitter/Receiver with UTOPIA Interface
2.8 FEAC Channel and HDLC Data Link Programming
100046C
Conexant
2-49
2.8.4.1 Receiver
Operation
The receiver implements an HDLC data link per ITU standard Q.921. The
functions provided by the data link receiver circuitry are transparency-zero
removal, FCS checking, idle flag reception, and abort flag reception. There are no
restrictions on the total length of the message. Q.921 requires that all messages be
an integral number of 8-bit bytes. If the receiver receives a message that is not an
integral number of bytes, the receiver status indicates a message received with
bad FCS. The per-byte reception times are equivalent to those given for the
transmitter for any particular mode.
The receiver powers up in an indeterminate state. It is initialized by the receipt
of an idle flag (0x7E) on the link, which sets Idle Code Received = 1 in the data
link status register (bits 13-8 of 0x60). When the idle flag is removed from the
link and a message starts coming in, the receiver removes stuffed 0s and writes
the resulting data to the receive data link buffer beginning with the least
significant byte of 0x58 and counting up to the most significant byte of 0x5B.
When the first four bytes have been written, the processor is interrupted to
read the data out of the buffer. The processor has 4 byte intervals to read the data
before it is overwritten with new data. The interrupt is cleared when the processor
reads DL_CTRL_STAT. The status register indicates a message in progress at this
time:
Idle Code Received = 0
RxBytes[2:0] = 3
If the upper half of the buffer had just been filled, the status register indicates
RxBytes[2:0] = 7, and locations 4 through 7 must be read during the next 4 byte
intervals to retrieve the message.
When the last block of data has been received, the processor is again
interrupted. This time, the data link status register indicates the end of message:
Idle Code Received = 1
The RxBytes[2:0] = n portion of the register indicates the highest-numbered
location that was written in the receive buffer. Locations 0 to n or 4 to m (where
n = 0 to 3 and m = 4 to 7) must be read to retrieve the data depending on what has
already been read at the previous interrupt. The two highest-numbered locations
contain the FCS that was received at the end of the message. A new incoming
message always starts in the opposite buffer half from where the previous
message ended to prevent overwriting of previously received bytes and allow the
processor time to retrieve those bytes. For example, if a message ended in buffer
0x5A or 0x5B, the next message received would be stored starting in 0x58. If a
message ended in buffer 0x58 or 0x59, the next message received would be stored
starting in 0x5A.
If the received message is a multiple of 8 bytes, then when the processor is
interrupted to read the last block of data, the FCS has yet to be received. In this
event, the processor is again interrupted when the FCS has been checked, and an
idle flag received. The data link status register shows RxBytes[2:0] = 1 (or 5),
FCS good or bad, and Idle Code Received = 1; and the FCS that was received will
be in locations 0 and 1 (or 4 and 5). Again, the data must be read out during the
next 4 byte intervals, or it may be overwritten by a new incoming message.
相關PDF資料 |
PDF描述 |
|---|---|
| 28C010TRPDB-12 | 150 x 32 pixel format, LED Backlight available |
| 28C010TRT1DE-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1DE-20 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-20 | 1 Megabit (128K x 8-Bit) EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 282332-2 | 制造商:TE Connectivity 功能描述: |
| 282-333 | 制造商:WAGO Innovative Connections 功能描述:END PLATE RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO Innovative Connections 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK; Series:282; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks; Color:Orange; Mounting Type:DIN Rail ;RoHS Compliant: Yes |
| 2823337 | 功能描述:工業(yè)繼電器 ST-REL4-KG120/21-21 RoHS:否 制造商:TE Connectivity / Kilovac 觸點形式:1 Form A (SPST-NO) 觸點電流額定值: 線圈電壓:9 VDC to 36 VDC 線圈電阻:38 Ohms 線圈電流: 切換電壓: 安裝風格:Panel 觸點材料:Silver Palladium |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:End Plate 2 mm Thick-Color Grey For Use With Rail Mounted Terminal Block 制造商:WAGO 功能描述:GREY END PLATE 制造商:WAGO Innovative Connections 功能描述:END PLATE, 2MM, GREY; Series:-; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks ;RoHS Compliant: Yes |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:END PLATE 制造商:WAGO 功能描述:END PLATE |
發(fā)布緊急采購，3分鐘左右您將得到回復。