- 您現在的位置：買賣IC網 > PDF目錄371438 > 29F016-90 (Macronix International Co., Ltd.) 16M-BIT [2M X 8] CMOS EQUAL SECTOR FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29F016-90 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 16M-BIT [2M X 8] CMOS EQUAL SECTOR FLASH MEMORY |
| 中文描述： | 1,600位[2米x 8]的CMOS平等部門閃存 |
| 文件頁數： | 6/37頁 |
| 文件大?。?/td> | 888K |
| 代理商： | 29F016-90 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
6
P/N:PM0590
REV. 1.4, NOV. 21, 2002
MX29F016
First Bus
Cycle
Addr
XXXH
RA
555H
555H
Second Bus
Cycle
Addr
Third Bus
Cycle
Addr
Fourth Bus
Cycle
Addr
Fifth Bus
Cycle
Addr
Sixth Bus
Cycle
Addr
Command
Bus
Cycle
1
1
4
4
Data
F0H
RD
AAH
AAH
Data
Data
Data
Data
Data
Reset
Read
Read Silicon ID
Sector Group Protect
Verify
Program
Chip Erase
Sector Erase
Sector Erase Suspend
Sector Erase Resume
2AAH 55H
2AAH 55H
555H
555H
90H
90H
ADI
SGA
X02H 01H
PA
555H
555H
DDI
00H
4
6
6
1
1
555H
555H
555H
XXXH
XXXH
AAH
AAH
AAH
B0H
30H
2AAH 55H
2AAH 55H
2AAH 55H
555H
555H
555H
A0H
80H
80H
PD
AAH
AAH
2AAH 55H
2AAH 55H
555H 10H
SA
30H
TABLE1. SOFTWARE COMMAND DEFINITIONS
Note:
1. ADI = Address of Device identifier; A1=0, A0 = 0 for manufacture code,A1=0, A0 = 1 for device code.
(Refer to Table 3)
DDI = Data of Device identifier : C2H for manufacture code, ADH for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2.PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address of the sector to be erased.
SGA = Address of the Sector Group Address bits A18-A20 select a uniqul sector group.
3.The system should generate the following address patterns: 555H or 2AAH to Address A10~A0 .
Address bit A11~A20=X=Don't care for all address commands except for Program Address (PA) and Sector
Address (SA). Write Sequence may be initiated with A11~A20 in either state.
4.For Sector Group Protect Verify Operation : If read out data is 01H, it means the sector has been protected.If read
out data is 00H,it means the sector is still not being protected.
COMMAND DEFINITIONS
Device operations are selected by writing specific address
and data sequences into the command register. Writing
incorrect address and data values or writing them in the
improper sequence will reset the device to the read mode.
Table 1 defines the valid register command sequences.
Note that the Erase Suspend (B0H) and Erase Resume
(30H) commands are valid only while the Sector Erase
operation is in progress.
相關PDF資料 |
PDF描述 |
|---|---|
| 29F022B-12 | 2M-BIT[256K x 8]CMOS FLASH MEMORY |
| 29F022B-120 | 2M-BIT[256K x 8]CMOS FLASH MEMORY |
| 29F022B-55 | 2M-BIT[256K x 8]CMOS FLASH MEMORY |
| 29F022B-70 | 2M-BIT[256K x 8]CMOS FLASH MEMORY |
| 29F022B-90 | 2M-BIT[256K x 8]CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29F016D70E4D | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 29F016D-70E4D | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 29F020 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| 29F022B-12 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT[256K x 8]CMOS FLASH MEMORY |
| 29F022B-120 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT[256K x 8]CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。