- 您現在的位置：買賣IC網 > PDF目錄371440 > 29LV800TE (Fujitsu Limited) 8M (1M x 8/512 K x 16) BIT PDF資料下載
參數資料
| 型號： | 29LV800TE |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8M (1M x 8/512 K x 16) BIT |
| 中文描述： | 8米（3米x五百一十二分之八畝× 16）位 |
| 文件頁數： | 17/58頁 |
| 文件大?。?/td> | 292K |
| 代理商： | 29LV800TE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
MBM29LV800TE/BE
60/70/90
16
I
FUNCTIONAL DESCRIPTION
Read Mode
The MBM29LV800TE/BE have two control functions which must be satisfied in order to obtain data at the outputs.
CE is the power control and should be used for a device selection. OE is the output control and should be used
to gate data to the output pins if a device is selected.
Address access time (t
ACC
) is equal to delay from stable addresses to valid output data. The chip enable access
time (t
CE
) is the delay from stable addresses and stable CE to valid data at the output pins. The output enable
access time is the delay from the falling edge of OE to valid data at the output pins (Assuming the addresses
have been stable for at least t
ACC
-t
OE
time) . When reading out data without changing addresses after power-up,
it is necessary to input hardware reset or change CE pin from “H” or “L”
Standby Mode
There are two ways to implement the standby mode on the MBM29LV800TE/BE devices, one using both the
CE and RESET pins; the other via the RESET pin only.
When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at V
CC
±
0.3 V.
Under this condition, the current consumed is less than 5
μ
A. The device can be read with standard access time
(t
CE
) from either of these standby modes. During Embedded Algorithm operation, V
CC
active current (I
CC2
) is
required even CE
=
“H”.
When using the RESET pin only, a CMOS standby mode is achieved with RESET input held at V
SS
±
0.3 V
(CE
=
“H” or “L”) . Under this condition the current consumed is less than 5
μ
A. Once the RESET pin is taken
high, the device requires t
RH
as wake up time for outputs to be valid for read access.
In the standby mode, the outputs are in the high impedance state, independently of the OE input.
Automatic Sleep Mode
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29LV800TE/BE data. This mode can be useful in the application such as handy terminal which requires
low power consumption.
To activate this mode, MBM29LV800TE/BE automatically switches themselves to low power mode when
MBM29LV800TE/BE addresses remain stable during access time of 150 ns. It is not necessary to control CE,
WE, and OE on the mode. Under the mode, the current consumed is typically 1
μ
A (CMOS Level) .
Since the data are latched during this mode, the data are read-out continuously. If the addresses are changed,
the mode is canceled automatically, and MBM29LV800TE/BE read-out the data for changed addresses.
Output Disable
With the OE input at a logic high level (V
IH
) , the output from the devices is disabled. This will cause the output
pins to be in a high impedance state.
Autoselect
The autoselect mode allows the reading out of a binary code from the devices and will identify its manufacturer
and type. This mode is intended for use by programming equipment for the purpose of automatically matching
the devices to be programmed with its corresponding programming algorithm. This mode is functional over the
entire temperature range of the devices.
To activate this mode, the programming equipment must force V
ID
(11.5 V to 12.5 V) on address pin A
9
. Two
identifier bytes may then be sequenced from the devices outputs by toggling address A
0
from V
IL
to V
IH
. All
addresses are DON’T CARES except A
0
, A
1
, A
6
, and A
-1
. (See “MBM29LV800TE/BE Sector Protection Verify
Autoselect Codes” in “
DEVICE BUS OPERATION”.)
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29LV800TE/BE are erased or programmed in a system without access to high voltage on the A
9
pin. The
command sequence is illustrated in “MBM29LV800TE/BE Command Definitions” in “
TION”. (Refer to Autoselect Command section.)
DEVICE BUS OPERA-
相關PDF資料 |
PDF描述 |
|---|---|
| 29PL256N | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| 29PS | 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches |
| 29SL800CB-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29SL800CT-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29U194A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29M132 | 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor |
| 29M30050R008BL | 制造商:Micro Plastics Inc 功能描述: |
| 29M426 | 制造商:Honeywell Sensing and Control 功能描述: |
| 29M428 | 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor |
| 29M455 | 制造商:Clarostat 功能描述:_ |
發布緊急采購，3分鐘左右您將得到回復。