參數資料
型號: 29LV800TE
廠商: Fujitsu Limited
英文描述: 8M (1M x 8/512 K x 16) BIT
中文描述: 8米(3米x五百一十二分之八畝× 16)位
文件頁數: 19/58頁
文件大?。?/td> 292K
代理商: 29LV800TE
MBM29LV800TE/BE
60/70/90
18
Extended Sector Protection
In addition to normal sector protection, the MBM29LV800TE/BE have Extended Sector Protection as extended
function. This function enables to protect sector by forcing V
ID
on RESET pin and write a commnad sequence.
Unlike conventional procedure, it is not necessary to force V
ID
and control timing for control pins. The only RESET
pin requires V
ID
for sector protection in this mode. The extended sector protect requires V
ID
on RESET pin. With
this condition the operation is initiated by writing the set-up command (60h) into the command register. Then
the sector addresses pins (A
18
, A
17
, A
16
, A
15
, A
14
, A
13
and A
12
) and (A
6
, A
1
, A
0
)
=
(0, 1, 0) should be set to be
protected (recommend to set V
IL
for the other addresses pins) , and write extended sector protect command
(60h) . A sector is generally protected in 250
μ
s. To verify programming of the protection circuitry, the sector
addresses pins (A
18
, A
17
, A
16
, A
15
, A
14
, A
13
and A
12
) and (A
6
, A
1
, A
0
)
=
(0, 1, 0) should be set and write a command
(40h) . Following the command write, a logical “1” at device output DQ
0
produces for protected sector in the read
operation. If the output is logical “0”, repeat to write extended sector protect command (60h) again. To terminate
the operation, it is necessary to set RESET pin to V
IH
(refer to “Extended Sector Protection Algorithm” in
I
FLOW CHART”) .
RESET
Hardware Reset
The MBM29LV800TE/BE devices may be reset by driving the RESET pin to V
IL
. The RESET pin has pulse
requirement and has to be kept low (V
IL
) for at least “t
RP
” in order to properly reset the internal state machine.
Any operation in the process of being executed is terminated and the internal state machine is reset to the read
mode “t
READY
” after the RESET pin goes low. Furthermore once the RESET pin goes high, the devices require
an additional t
RH
before it will allow read access. When the RESET pin is low, the devices will be in the standby
mode for the duration of the pulse and all the data output pins will be tri-stated. If hardware reset occurs during
program or erase operation, the data at that particular location is corrupted. Note that the RY/BY output signal
should be ignored during the RESET pulse. See “RESET, RY/BY Timing Diagram” in “
I
TIMING DIAGRAM”
for the timing diagram. Refer to Temporary Sector Unprotection for additional functionality.
If hardware reset occurs during Embedded Erase Algorithm, the erasing sector (s) cannot be used.
相關PDF資料
PDF描述
29PL256N 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
29PS 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches
29SL800CB-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY
29SL800CT-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY
29U194A The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
相關代理商/技術參數
參數描述
29M132 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor
29M30050R008BL 制造商:Micro Plastics Inc 功能描述:
29M426 制造商:Honeywell Sensing and Control 功能描述:
29M428 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor
29M455 制造商:Clarostat 功能描述:_