- 您現在的位置：買賣IC網 > PDF目錄371440 > 29LV800TE (Fujitsu Limited) 8M (1M x 8/512 K x 16) BIT PDF資料下載
參數資料
| 型號： | 29LV800TE |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8M (1M x 8/512 K x 16) BIT |
| 中文描述： | 8米（3米x五百一十二分之八畝× 16）位 |
| 文件頁數： | 22/58頁 |
| 文件大小： | 292K |
| 代理商： | 29LV800TE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
MBM29LV800TE/BE
60/70/90
21
“Embedded Erase
TM
Algorithm” in “
I
FLOW CHART” illustrates the Embedded Erase
TM
Algorithm using typical
command strings and bus operations.
Erase Suspend/Resume
The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads
from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase
operation which includes the time-out period for sector erase. Writting the Erase Suspend command during the
Sector Erase time-out results in immediate termination of the time-out period and suspension of the erase
operation.
Writing the Erase Resume command resumes the erase operation. The addresses are DON’T CARES when
writing the Erase Suspend or Erase Resume command.
When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum
of “t
SPD
” to suspend the erase operation. When the devices have entered the erase-suspended mode, the RY/
BY output pin and the DQ
7
bit will be at logic “1”, and DQ
6
will stop toggling. The user must use the address of
the erasing sector for reading DQ
6
and DQ
7
to determine if the erase operation has been suspended. Further
writes of the Erase Suspend command are ignored.
When the erase operation has been suspended, the devices default to the erase-suspend-read mode. Reading
data in this mode is the same as reading from the standard read mode except that the data must be read from
sectors that have not been erase-suspended. Successively reading from the erase-suspended sector will cause
DQ
2
to toggle while the device is in the erase-suspend-read mode (See the section on DQ
2
) .
After entering the erase-suspend-read mode, the user can program the device by writing the appropriate com-
mand sequence for Program. This program mode is known as the erase-suspend-program mode. Again, pro-
gramming in this mode is the same as programming in the regular Program mode except that the data must be
programmed to sectors that are not erase-suspended. Successively reading from the erase-suspended sector
while the devices are in the erase-suspend-program mode will cause DQ
2
to toggle. The end of the erase-
suspended Program operation is detected by the RY/BY output pin, Data polling of DQ
7
, or by the Toggle Bit I
(DQ
6
) which is the same as the regular Program operation. Note that DQ
7
must be read from the Program address
while DQ
6
can be read from any address.
To resume the operation of Sector Erase, the Resume command (30h) should be written. Any further writes of
the Resume command at this point will be ignored. Another Erase Suspend command can be written after the
chip has resumed erasing.
Extended Command
(1) Fast Mode
MBM29LV800TE/BE have Fast Mode function. This mode dispenses with the initial two unclock cycles required
in the standard program command sequence by writing Fast Mode command into the command register. In this
mode, the required bus cycle for programming is two cycles instead of four bus cycles in standard program
command. In Fast Mode, do not write any command other than the fast program/fast mode reset command. The
read operation is also executed after exiting this mode. To exit this mode, it is necessary to write Fast Mode
Reset command into the command register (Refer to “Embedded Programming Algorithm for Fast Mode” in “
I
FLOW CHART”) . The V
CC
active current is required even CE
=
V
IH
during Fast Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program
Algorithm is executed by writing program set-up command (A0h) and data write cycles (PA/PD) (Refer to
“Embedded Programming Algorithm for Fast Mode” in “
I
FLOW CHART”) .
相關PDF資料 |
PDF描述 |
|---|---|
| 29PL256N | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| 29PS | 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches |
| 29SL800CB-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29SL800CT-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29U194A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29M132 | 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor |
| 29M30050R008BL | 制造商:Micro Plastics Inc 功能描述: |
| 29M426 | 制造商:Honeywell Sensing and Control 功能描述: |
| 29M428 | 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor |
| 29M455 | 制造商:Clarostat 功能描述:_ |
發布緊急采購，3分鐘左右您將得到回復。