參數資料
型號： 73S1215F-EB-LITE
廠商： Maxim Integrated Products
文件頁數： 130/136頁
文件大?。?/td> 0K
描述： BOARD EVAL 73S1215F CBL/DOC/CD
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
系列： *
DS_1215F_003
73S1215F Data Sheet
Rev. 1.4
93
TX Control/Status Register (STXCtl): 0xFE06
0x00
This register is used to control transmission of data to the smart card. Some control and some status bits
are in this register.
Table 86: The STXCtl Register
MSB
LSB
I2CMODE
–
TXFULL TXEMTY TXUNDR LASTTX
TX/RXB BREAKD
Bit
Symbol
Function
STXCtl.7
I2CMODE
I2C Mode – When in sync mode and this bit is set, and when the RLen count
value = max or 0, the source of the smart card data for IO pin (or SIO pin) will
be connected to the IO bit in SCCtl (or SCECtl) register rather than the TX
FIFO. See the description for the Protocol Mode Register for more detail.
STXCtl.6
–
STXCtl.5
TXFULL
TX FIFO is full. Additional writes may corrupt the contents of the FIFO. This
bit it will remain set as long as the TX FIFO is full. Generates TX_Event
interrupt upon going full.
STXCtl.4
TXEMTY
1 = TX FIFO is empty, 0 = TX FIFO is not empty. If there is data in the TX
FIFO, the circuit will transmit it to the smart card if in transmit mode. In T=1
mode, if the LASTTX bit is set and the hardware is configured to transmit the
CRC/LRC, the TXEMTY will not be set until the CRC/LRC is transmitted. In
T=0, if the LASTTX bit is set, TXEMTY will be set after the last word has
been successfully transmitted to the smart card. Generates TXEVNT
interrupt upon going empty.
STXCtl.3
TXUNDR
TX Underrrun – (Read only) Asserted when a transmit under-run condition
has occurred. An under-run condition is defined as an empty TX FIFO when
the last data word has been successfully transmitted to the smart card and
the LASTTX bit was not set. No special processing is performed by the
hardware if this condition occurs. Cleared when read by firmware. This bit
generates TXERR interrupt.
STXCtl.2
LASTTX
Last TX Byte – Set by firmware (in both T=0 and T=1) when the last byte in
the current message has been written into the transmit FIFO. In T=1 mode,
the CRC/LRC will be appended to the message. Should be set after the last
byte has been written into the transmit FIFO. Should be cleared by firmware
before writing first byte of next message into the transmit FIFO. Used in T=0
to determine when to set TXEMTY.
STXCtl.1
TX/RXB
1 = Transmit mode, 0 = Receive mode. Configures the hardware to be
receiving from or transmitting to the smart card. Determines which counters
should be enabled. This bit should be set to receive mode prior to switching
to another interface. Setting and resetting this bit shall initialize the CRC
logic. If LASTTX is set, this bit can be reset to RX mode and UART logic will
automatically change mode to RX when TX operation is completed
(TX_Empty =1).
STXCtl.0
BREAKD
Break Detected – (Read only) 1 = A break has been detected on the I/O line
indicating that the smart card detected a parity error. Cleared when read.
This bit generates TXERR interrupt.
相關PDF資料
PDF描述
V375C48T75B2 CONVERTER MOD DC/DC 48V 75W
RCC07DRAS-S734 CONN EDGECARD 14POS .100 R/A PCB
ZRC400F01TC IC VREF SHUNT PREC 4.096V SOT-23
V72C12E150B2 CONVERTER MOD DC/DC 12V 150W
H1AXS-2636G IDC CABLE - HSC26S/AE26G/X
相關代理商/技術參數
參數描述
73S1217F 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More
73S1217F-68IM/F 功能描述:8位微控制器 -MCU Bus Pwr’d 80515 SoC w/USB 7816/EMV PINpd RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
73S1217F-68IM/F/P 功能描述:IC SMART CARD READER PROG 68-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:73S12xx 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR
73S1217F-68IMR/F 功能描述:8位微控制器 -MCU Bus Pwr’d 80515 SoC w/USB 7816/EMV PINpd RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
73S1217F-68IMR/F/P 功能描述:IC SMART CARD READER PROG 68-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:73S12xx 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*