- 您現在的位置：買賣IC網 > PDF目錄1887 > 73S1217F-68MR/F/PE (Maxim Integrated Products)IC SOC SMART CARD READER 68QFN PDF資料下載
參數資料
| 型號： | 73S1217F-68MR/F/PE |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 121/140頁 |
| 文件大小： | 0K |
| 描述： | IC SOC SMART CARD READER 68QFN |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁當前第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁
DS_1217F_002
73S1217F Data Sheet
Rev. 1.2
81
1.7.17.2
Answer to Reset Processing
A card insertion event generates an interrupt to the firmware, which is then responsible for the
configuration of the electrical interface, the UART and activation of the card. The activation sequencer
goes through the power up sequence as defined in the ISO 7816-3 specification. An asynchronous
activation timing diagram is shown in Figure 18. After the card RST is de-asserted, the firmware instructs
the hardware to look for a TS byte that begins the ATR response. If a response is not provided within the
pre-programmed timeout period, an interrupt is generated and the firmware can then take appropriate
action, including instructing the 73S1217F to begin a deactivation sequence. Once commanded, the
deactivation sequencer goes through the power down sequence as defined in the ISO 7816-3
specification. If an ATR response is received, the hardware looks for a TS byte that determines
direct/inverse convention. The hardware handles the indirect convention conversion such that the
embedded firmware only receives direct convention. This feature can be disabled by firmware within the
SByteCtl register. Parity checking and break generation is performed on the TS byte unless disabled by
firmware. If during the card session, a card removal, over-current or other error event is detected, the
hardware will automatically perform the deactivation sequence and then generate an interrupt to the
firmware. The firmware can then perform any other error handling required for proper system operation.
Smart card RST, I/O and CLK, C4, C8 shall be low before the end of the deactivation sequence. Figure
19 shows the timing for a deactivation sequence.
VCCSEL
bits
VCC
VCCOK bit
RSTCRD bit
RST
CLK
IO
t1
t2
t3
t4
t5
tto
See Note
ATR starts
t4
SELSC
bits
t1: SELSC.1 bit set (selects internal ICC interface) and a non-zero value in VCCSEL bits (calling for
a value of Vcc of 1.8, 3.0, or 5.0 volts) will begin the activation sequence. t1 is the time for Vcc to rise
to acceptable level, declared as Vcc OK (bit VCCOK gets set). This time depends on filter capacitor
value and card Icc load.
tto: The time allowed for Vcc to rise to Vcc OK status after setting of the VCCSEL bits. This time is
generated by the VCCTMR counter. If Vcc OK is not set, (bit VCCOK) at this time, a deactivation will
be initiated. VCCSEL bits are not automatically cleared. The firmware must clear the VCCSEL bits
before starting a new activation.
t2: Time from VCCTmr timeout and VCC OK to IO reception (high), typically 2-3 CLK cycles if
RDYST = 0. If RDYST = 1, t2 starts when VCCOK = 1.
t3: Time from IO = high to CLK start, typically 2-3 CLK cycles.
t4: Time allowed for start of CLK to de-assertion of RST. Programmable by the RLength register.
t5: Time allowed for ATR timeout, set by the STSTO register.
Note: If the RSTCRD bit is set, RST is asserted (low). Upon clearing RSTCRD bit, RST will be
de-asserted after t4.
Figure 18: Asynchronous Activation Sequence Timing
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010C-ILR/F | IC SMART CARD INTERFACE 28-SOIC |
| 73S8010R-ILR/F | IC SMART CARD INTERFACE 28-SOIC |
| 73S8014R-IL/F | IC SMART CARD 7816 EMV 20-SOIC |
| 73S8014RN-ILR/F | IC SMART CARD 7816 EMV 20-SOIC |
| 73S8023C-IMR/F | IC SMART CARD INTERFACE 32-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S1217F-EB | 功能描述:開發板和工具包 - 8051 73S1217F Eval Brd (Usb Cable, Doc. Cd) RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1217F-EB-Lite | 功能描述:開發板和工具包 - 8051 73S1217F EVB Lite w/Plug & Play/Usb RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1217F-IMR/F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More |
| 73S13B | 制造商:QUARTZCOM 制造商全稱:QUARTZCOM the communications company 功能描述:-20 ~ +70 °C commercia l application -30 ~ +75 °C on request |
| 73S5040G01X0A | 制造商:NEX Computers 功能描述:INTEL 40GB SSD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。