- 您現在的位置：買賣IC網 > PDF目錄1887 > 73S1217F-68MR/F/PE (Maxim Integrated Products)IC SOC SMART CARD READER 68QFN PDF資料下載
參數資料
| 型號： | 73S1217F-68MR/F/PE |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 136/140頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SOC SMART CARD READER 68QFN |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁當前第136頁第137頁第138頁第139頁第140頁
DS_1217F_002
73S1217F Data Sheet
Rev. 1.2
95
TX Control/Status Register (STXCtl): 0xFE06
0x00
This register is used to control transmission of data to the smart card. Some control and some status bits
are in this register.
Table 85: The STXCtl Register
MSB
LSB
I2CMODE
–
TXFULL TXEMTY TXUNDR LASTTX
TX/RXB BREAKD
Bit
Symbol
Function
STXCtl.7
I2CMODE
I2C Mode – When in sync mode and this bit is set, and when the RLen count
value = max or 0, the source of the smart card data for IO pin (or SIO pin) will
be connected to the IO bit in SCCtl (or SCECtl) register rather than the TX
FIFO. See the description for the Protocol Mode Register for more detail.
STXCtl.6
–
STXCtl.5
TXFULL
TX FIFO is full. Additional writes may corrupt the contents of the FIFO. This
bit it will remain set as long as the TX FIFO is full. Generates a TX_Event
interrupt upon going full.
STXCtl.4
TXEMTY
1 = TX FIFO is empty, 0 = TX FIFO is not empty. If there is data in the TX
FIFO, the circuit will transmit it to the smart card if in transmit mode. In T=1
mode, if the LASTTX bit is set and the hardware is configured to transmit the
CRC/LRC, the TXEMTY will not be set until the CRC/LRC is transmitted. In
T=0, if the LASTTX bit is set, TXEMTY will be set after the last word has
been successfully transmitted to the smart card. Generates a TXEVNT
interrupt upon going empty.
STXCtl.3
TXUNDR
TX Underrrun – (Read only) Asserted when a transmit under-run condition
has occurred. An under-run condition is defined as an empty TX FIFO when
the last data word has been successfully transmitted to the smart card and
the LASTTX bit was not set. No special processing is performed by the
hardware if this condition occurs. Cleared when read by firmware. This bit
generates a TXERR interrupt.
STXCtl.2
LASTTX
Last TX Byte – Set by firmware (in both T=0 and T=1) when the last byte in
the current message has been written into the transmit FIFO. In T=1 mode,
the CRC/LRC will be appended to the message. Should be set after the last
byte has been written into the transmit FIFO. Should be cleared by firmware
before writing first byte of next message into the transmit FIFO. Used in T=0
to determine when to set TXEMTY.
STXCtl.1
TX/RXB
1 = Transmit mode, 0 = Receive mode. Configures the hardware to be
receiving from or transmitting to the smart card. Determines which counters
should be enabled. This bit should be set to receive mode prior to switching
to another interface. Setting and resetting this bit shall initialize the CRC
logic. If LASTTX is set, this bit can be reset to RX mode and UART logic will
automatically change mode to RX when TX operation is completed
(TX_Empty =1).
STXCtl.0
BREAKD
Break Detected – (Read only) 1 = A break has been detected on the I/O line
indicating that the smart card detected a parity error. Cleared when read.
This bit generates a TXERR interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010C-ILR/F | IC SMART CARD INTERFACE 28-SOIC |
| 73S8010R-ILR/F | IC SMART CARD INTERFACE 28-SOIC |
| 73S8014R-IL/F | IC SMART CARD 7816 EMV 20-SOIC |
| 73S8014RN-ILR/F | IC SMART CARD 7816 EMV 20-SOIC |
| 73S8023C-IMR/F | IC SMART CARD INTERFACE 32-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S1217F-EB | 功能描述:開發板和工具包 - 8051 73S1217F Eval Brd (Usb Cable, Doc. Cd) RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1217F-EB-Lite | 功能描述:開發板和工具包 - 8051 73S1217F EVB Lite w/Plug & Play/Usb RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1217F-IMR/F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Bus-Powered 80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More |
| 73S13B | 制造商:QUARTZCOM 制造商全稱:QUARTZCOM the communications company 功能描述:-20 ~ +70 °C commercia l application -30 ~ +75 °C on request |
| 73S5040G01X0A | 制造商:NEX Computers 功能描述:INTEL 40GB SSD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。