- 您現在的位置：買賣IC網 > PDF目錄1888 > 78Q2120C09-64CGTR/F (Maxim Integrated Products)TXRX 10/100 BASE 3.3V 64-LQFP PDF資料下載
參數資料
| 型號： | 78Q2120C09-64CGTR/F |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX 10/100 BASE 3.3V 64-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,500 |
| 類型： | 以太網 |
| 驅動器/接收器數： | 4/4 |
| 規程： | MII |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
78Q2120C
10/100BASE-TX
Transceiver
Page: 2 of 35
2009 Teridian Semiconductor Corporation
Rev 1.3
FUNCTIONAL DESCRIPTION
GENERAL
Power Management
The 78Q2120C has three power saving modes:
Chip Power-Down
Receive Power Management
Transmit High Impedance Mode
Chip power-down is activated by setting the PWRDN
bit in MII register MR0.11 or pulling high the PWRDN
pin. When the chip is in the power-down mode, all
on-chip circuitry is shut off, and the device
consumes minimum power.
While in the power-
down state, the 78Q2120C still responds to
management transactions.
Receive power management (RXCC mode) is
activated by setting the RXCC bit in MII register
MR16.0. In this mode of operation, the adaptive
equalizer, the clock recovery phase lock loop (PLL),
and all other receive circuitry will be powered down
when no valid MLT-3 signal is present at the UTP
receive line interface. As soon as a valid signal is
detected, all circuits will automatically be powered
up to resume normal operation. During this mode of
operation, RX_CLK will be inactive when there is no
data being received. Note that the RXCC mode is
not supported during 10BASE-T operation.
Transmit high impedance mode is activated by
setting the TXHIM bit in MII register MR16.12. In this
mode of operation, the transmit UTP drivers are in a
high impedance state and TX_CLK is tri-stated. A
weak internal pull-up is enabled on TX_CLK. The
receive circuitry remains fully operational. The
default state of MR16.12 is a logic low for disabling
the transmit high impedance mode. The transmitter
is fully functional when MR16.12 is cleared.
Analog Biasing and Supply Regulation
The 78Q2120C requires no external component to
generate on-chip bias voltages and currents. High
accuracy is maintained through a closed-loop
trimmed biasing network.
On-chip digital logic runs off an internal voltage
regulator.
Hence only a single Vcc supply is
required to power-up the device.
The on-chip
regulator is not affected by the power-down mode.
Clock Selection
The 78Q2120C will use the on-chip crystal oscillator
as the clock source if the CKIN pin is tied low. In this
mode of operation, a 25MHz crystal should be
connected between the XTLP and XTLN pins.
Alternatively, an external 25MHz clock signal can be
connected to the CKIN pin. The chip senses activity
on the CKIN pin, and will automatically configure itself
to use the external clock. In this mode of operation, a
crystal is not required and the XTLP and XTLN pins
should be left floating or connected together.
Transmit Clock Generation
The
transmitter
uses
an
on-chip
frequency
synthesizer to generate the transmit clock. In
100BASE-TX operation, the synthesizer multiplies the
reference clock by 5 to obtain the internal 125MHz
serial transmit clock.
In 10BASE-T mode, it
generates an internal 20MHz transmit clock by
multiplying the 25MHz reference clock by 4/5. The
synthesizer references either the local 25 MHz crystal
oscillator, or the externally applied clock, depending
on the selected mode of operation.
Receive Signal Qualification
The integrated signal qualifier has separate squelch
and unsquelch thresholds. It also includes a built-in
timer to ensure fast and accurate signal detection and
line noise rejection. Upon detection of two or more
valid 10BASE-T or 100BASE-TX pulses on the line
receive port, signal detect is indicated. The signal
detect threshold is then lowered by about 40%. All
adaptive circuits are released from their initial states
and allowed to lock onto the incoming data.
In
100BASE-TX operation, signal detect is de-asserted
when no signal is presented for a period of about
1.2us. In 10BASE-T operation, signal detect is de-
asserted whenever no Manchester data is received. In
either case, the signal detect threshold will return to the
squelched level whenever the signal detect indication
is de-asserted. Signal detect is also used to control the
operation of the clock/data recovery circuit to assure
fast acquisition.
Receive Clock Recovery
In 100BASE-TX mode, the 125MHz receive clock is
extracted using a digital DLL-based loop. When no
receive signal is present, the CDR is directed to lock
onto the 125MHz transmit serial clock. When signal
detect is asserted, the CDR will use the received MLT-
3 signal as the clock reference. The recovered clock is
used to re-time the data signal and for conversion of
the data to NRZ format.
In 10BASE-T mode, the 10MHz receive clock is
recovered digitally from the Manchester data using a
DLL locked to the reference clock.
When
Manchester-coded preambles are detected, the
相關PDF資料 |
PDF描述 |
|---|---|
| 78Q2133/F | TXRX 10/100 MDIX 3.3V IND 32-QFN |
| 78Q8392LA03-28CHR/F | TXRX 10BASE 2/5 ETH COAX 28-PLCC |
| 78Q8430-100IGT/F | IC LAN MEDIA ACCESS CTLR 100LQFP |
| A1020B-1CQ84C | IC FPGA 2K GATES 84-CQFP COM |
| A1225A-1PQ100C | IC FPGA 2500 GATES 100-PQFP COM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78Q2120C09-CGTR/F | 功能描述:以太網 IC 10-100 Fast Ethernet Transceiver RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 78Q2120C09-DB | 功能描述:以太網開發工具 78Q2120C09 Demo Boa RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| 78Q2120-CGT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2123 | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:10/100BASE-TX Transceiver |
| 78Q2123/F | 功能描述:以太網 IC 10/100 Fast Ethernet MicroPHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。