2009 Teridian Semiconductor Corporation Rev 1.3 SQE T" />
參數資料
型號： 78Q2120C09-64CGTR/F
廠商： Maxim Integrated Products
文件頁數： 30/35頁
文件大?。?/td> 0K
描述： TXRX 10/100 BASE 3.3V 64-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1,500
類型： 以太網
驅動器/接收器數： 4/4
規程： MII
電源電壓： 3 V ~ 3.6 V
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 帶卷 (TR)
78Q2120C
10/100BASE-TX
Transceiver
Page: 4 of 35
2009 Teridian Semiconductor Corporation
Rev 1.3
SQE TEST
The 78Q2120C supports the Signal Quality Error
(SQE) function detailed in IEEE-802.3.
At an
interval of 1
s after each negative transition of the
TXEN pin in 10BASE-T mode, the COL pin will go
high for a period of 1
s. SQE is not signaled during
transmission after collision is detected.
SQE is
automatically disabled when repeater mode is
enabled.
This function can be disabled through
register bit MR16.11.
Natural Loopback
When
enabled,
whenever
the
78Q2120C
is
transmitting and not receiving on the twisted pair
media (10BASE-T Half Duplex mode), data on the
TXD[3:0] pins is looped back onto the RXD[3:0] pins.
During a collision, data from the RXI pins is routed to
the RXD[3:0] pins. The natural loopback function is
enabled through register bit MR16.10.
Repeater Mode
When the RPTR pin is high or register bit MR16.15
is set, the 78Q2120C is placed in repeater mode. In
this mode, full duplex operation is prohibited, CRS
responds only to receive activity and, in 10BASE-T
mode, the SQE test function is disabled.
AUTO-NEGOTIATION
The 78Q2120C supports the auto-negotiation
functions of Clause 28 of IEEE-802.3 for 10/100
Mbps operation over copper wiring. This function
can be enabled via a pin selection or register
settings. If the ANEGA pin is tied high, the auto-
negotiation function defaults to ON and bit MR0.12
(ANEGEN) is high after reset. Software can disable
the auto-negotiation function by writing to bit
MR0.12. If the ANEGA pin is tied low, the function
defaults to OFF and bit MR0.12 is set low after reset
and cannot be written to.
The contents of register MR4 are sent to the
78Q2120C’s link partner during auto-negotiation
using fast link pulse coding. Bits MR4.8:5 reflect the
state of the TECH[2:0] pins after reset. If TECH[2:0]
= ‘111’, then all 4 bits are high. If TECH[2:0] = ‘001’,
then only bit 5 is high. After reset, software can
change any of these bits from a ‘1’ to a ‘0’; but not
from a ‘0’ to a ‘1’. Therefore, a technology permitted
by the setting of the TECH pins can be disabled, but
cannot be enabled through register selection.
With auto-negotiation enabled, the 78Q2120C will
start sending fast link pulses at power on, loss of link
or upon a command to restart. At the same time, it
will look for either 10BASE-T idle, 100BASE-TX idle,
or fast link pulses from its link partner. If either idle
pattern is detected, the 78Q2120C configures itself
in half-duplex mode at the appropriate speed. If it
detects fast link pulses, it decodes and analyzes the
link code transmitted by the link partner.
When
three identical link code words are received (ignoring
the acknowledge bit) the link code word is stored in
register MR5. Upon receiving three more identical
link code words, with the acknowledge bit set, the
78Q2120C configures itself to the highest priority
technology common to the two link partners. The
technology priorities are, in descending order:
100BASE-TX, Full Duplex
100BASE-TX, Half Duplex
10BASE-T, Full Duplex
10BASE-T, Half Duplex
Once auto-negotiation is complete, register bits
MR18.11:10 will reflect the actual speed and duplex
that was chosen.
If auto-negotiation fails to establish a link for any
reason, register bit MR18.12 will reflect this and auto
negotiation will restart from the beginning. Writing a
‘1’ to bit MR0.9(RANEG) will also cause auto-
negotiation to restart.
MEDIA INDEPENDENT INTERFACE
MII Transmit and Receive Operation
The MII interface on the 78Q2120C provides
independent transmit and receive paths for both
10Mb/s and 100Mb/s data rates as described in
Clause 22 of the IEEE-802.3 standard.
The transmit clock, TX_CLK, provides the timing
reference for the transfer of TX_EN, TXD[3:0], and
TX_ER signals from the MAC to the 78Q2120C.
TXD[3:0] is captured on the rising edge of TX_CLK
when TX_EN is asserted. TX_ER is also captured
on the rising edge of TX_CLK and is asserted by the
MAC to request that an error code group is to be
transmitted.
The assertion of TX_ER is ignored
when the 78Q2120C is operating in 10BASE-T
mode.
The receive clock, RX_CLK, provides the timing
reference to transfer RX_DV, RXD[3:0], and RX_ER
signals from the 78Q2120C to the MAC. RX_DV
transitions synchronously with respect to RX_CLK
and is asserted when the 78Q2120C is presenting
valid data on RXD[3:0]. RX_ER is asserted and is
synchronous to RX_CLK when a code group
violation has been detected in the current receive
packet.
相關PDF資料
PDF描述
78Q2133/F TXRX 10/100 MDIX 3.3V IND 32-QFN
78Q8392LA03-28CHR/F TXRX 10BASE 2/5 ETH COAX 28-PLCC
78Q8430-100IGT/F IC LAN MEDIA ACCESS CTLR 100LQFP
A1020B-1CQ84C IC FPGA 2K GATES 84-CQFP COM
A1225A-1PQ100C IC FPGA 2500 GATES 100-PQFP COM
相關代理商/技術參數
參數描述
78Q2120C09-CGTR/F 功能描述:以太網 IC 10-100 Fast Ethernet Transceiver RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
78Q2120C09-DB 功能描述:以太網開發工具 78Q2120C09 Demo Boa RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
78Q2120-CGT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver
78Q2123 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:10/100BASE-TX Transceiver
78Q2123/F 功能描述:以太網 IC 10/100 Fast Ethernet MicroPHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*