- 您現在的位置：買賣IC網 > PDF目錄378217 > 82801E (INTEL CORP) Intel 82801E Communications I/O Controller Hub (C-ICH) PDF資料下載
參數資料
| 型號： | 82801E |
| 廠商： | INTEL CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | Intel 82801E Communications I/O Controller Hub (C-ICH) |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PBGA421 |
| 封裝： | BGA-421 |
| 文件頁數： | 32/84頁 |
| 文件大?。?/td> | 1196K |
| 代理商： | 82801E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
Intel
82801E C-ICH
32
Advance Information Datasheet
SDA[2:0]
O
Secondary IDE Device Address:
These output signals are connected to the
corresponding signals on the secondary IDE connectors. They are used to
indicate which byte in either the ATA command block or control block is being
addressed.
SDCS1#
O
Secondary IDE Device Chip Selects for 100 Range:
This signal is for the
ATA command register block. This output signal is connected to the
corresponding signal on the secondary IDE connector.
SDCS3#
O
Secondary IDE Device Chip Select for 300 Range:
This signal is for the
ATA control register block. This output signal is connected to the
corresponding signal on the secondary IDE connector.
SDD[15:0]
I/O
Secondary IDE Device Data:
These signals directly drive the corresponding
signals on the secondary IDE connector. There is a weak internal pull-down
resistor on SDD[7].
SDDACK#
O
Secondary IDE Device DMA Acknowledge:
This signal directly drives the
DAK# signal on the secondary IDE connectors. This signal is asserted by the
82801E C-ICH to indicate to the IDE DMA slave device that a given data
transfer cycle (assertion of DIOR# or DIOW#) is a DMA data transfer cycle.
This signal is used in conjunction with the PCI bus master IDE function and is
not associated with any AT-compatible DMA channel.
SDDREQ
I
Secondary IDE Device DMA Request:
This input signal is directly driven
from the DRQ signals on the secondary IDE connector. It is asserted by the
IDE device to request a data transfer, and used in conjunction with the PCI
bus master IDE function. It is not associated with any AT-compatible DMA
channel. There is a weak internal pull-down resistor on SDDREQ.
SDIOR#
/(SDWSTB/
SRDMARDY#)
O
Secondary Disk I/O Read (PIO and Non-Ultra DMA):
This is the command
to the IDE device that it may drive data on the SDD lines. Data is latched by
the 82801E C-ICH on the deassertion edge of SDIOR#. The IDE device is
selected either by the ATA register file chip selects (SDCS1# or SDCS3#) and
the SDA lines, or the IDE DMA acknowledge (SDDAK#).
Secondary Disk Write Strobe (Ultra DMA Writes to Disk):
This is the data
write strobe for writes to disk. When writing to disk, the 82801E C-ICH drives
valid data on rising and falling edges of SDWSTB.
Secondary Disk DMA Ready (Ultra DMA Reads from Disk):
This is the
DMA ready for reads from disk. When reading from disk, the 82801E C-ICH
deasserts SRDMARDY# to pause burst data transfers.
SDIOW#
/(SDSTOP)
O
Secondary Disk I/O Write (PIO and Non-Ultra DMA):
This is the command
to the IDE device that it may latch data from the SDD lines. Data is latched by
the IDE device on the deassertion edge of SDIOW#. The IDE device is
selected either by the ATA register file chip selects (SDCS1# or SDCS3#) and
the SDA lines, or the IDE DMA acknowledge (SDDAK#).
Secondary Disk Stop (Ultra DMA):
The 82801E C-ICH asserts SDSTOP to
terminate a burst.
SERIRQ
I/O
Serial Interrupt Request:
This pin implements the serial interrupt protocol.
SERR#
I
System Error:
SERR# can be pulsed active by any PCI device that detects a
system error condition. Upon sampling SERR# active, the 82801E C-ICH has
the ability to generate an NMI, SMI#, or interrupt.
SIORDY
/(SDRSTB
/SWDMARDY#)
I
Secondary I/O Channel Ready (PIO):
This signal keeps the strobe active
(SDIOR# on reads, SDIOW# on writes) longer than the minimum width. It
adds wait states to SIO transfers.
Secondary Disk Read Strobe (Ultra DMA Reads from Disk)
: When reading
from disk, the 82801E C-ICH latches data from the disk on rising and falling
edges of SDRSTB.
Secondary Disk DMA Ready (Ultra DMA Writes to Disk)
: When writing to
disk, SWDMARDY# is deasserted by the disk to pause burst data transfers.
Table 6. 82801E C-ICH Signal Description (Sheet 8 of 11)
Signal
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| 82802AB | Firmware Hub (FWH) |
| 82802AC | Firmware Hub (FWH) |
| 8281 | LNB SUPPLY AND CONTROL-VOLTAGE REGULATORS |
| 8282 | OCTAL LATCH |
| 8282 | LNB SUPPLY AND CONTROL-VOLTAGE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 82801FB | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel I/O Controller Hub 6 (ICH6) Family |
| 82801FBM | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel I/O Controller Hub 6 (ICH6) Family |
| 82801FR | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel I/O Controller Hub 6 (ICH6) Family |
| 82801GBICH7 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel I/O Controller Hub 7 |
| 82801GBMICH7-M | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel I/O Controller Hub 7 |
發布緊急采購，3分鐘左右您將得到回復。