- 您現在的位置：買賣IC網 > PDF目錄376475 > 84072xxx (Electronic Theatre Controls, Inc.) MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, OCTAL TRANSPARENT D-TYPE LATCHES WITH THREE STATE OUTPUTS MONOLITIC SILICON PDF資料下載
參數資料
| 型號： | 84072xxx |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, OCTAL TRANSPARENT D-TYPE LATCHES WITH THREE STATE OUTPUTS MONOLITIC SILICON |
| 中文描述： | 微電路，數字化，高速的CMOS，八路透明D類鎖存器與三態輸出MONOLITIC硅 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 166K |
| 代理商： | 84072XXX |
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
SIZE
A
84072
REVISION LEVEL
F
SHEET
15
DSCC FORM 2234
APR 97
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method
1005 of MIL-STD-883.
b. T
A
= +125
°
C, minimum.
c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The
test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of
MIL-STD-883.
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein.
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
(see 3.5 herein).
a. End-point electrical parameters shall be as specified in table II herein.
b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as
specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to
radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device
classes must meet the postirradiation end-point electrical parameter limits as defined in table I at T
A
= +25
°
C
±
5
°
C,
after exposure, to the subgroups specified in table II herein.
c. When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied.
4.5 Methods of inspection. Methods of inspection shall be specified as follows:
4.5.1 Voltage and current. Unless otherwise specified, all voltages given are referenced to the microcircuit GND terminal.
Currents given are conventional current and positive when flowing into the referenced terminal.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes
Q and V or MIL-PRF-38535, appendix A for device class M.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
相關PDF資料 |
PDF描述 |
|---|---|
| 845HN | Sub-Miniature ?1 or 2 pole, 5-12 amps |
| 8480 | Input/Output Modules |
| 8481 | Input/Output Modules |
| 8482 | Input/Output Modules |
| 8483 | Input/Output Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 840730 | 功能描述:FUSE COVER .28 X 1.18 X .5" RoHS:是 類別:過電壓，電流，溫度裝置 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:基座 適用于相關產品:- 其它名稱:UAK-BE/L6 |
| 840730-1 | 制造商:TE Connectivity 功能描述:LGH-1L CERAMIC RECEPT - Bulk |
| 84073012A | 制造商:Texas Instruments 功能描述:Flip Flop D-Type Bus Interface Pos-Edge 1-Element 20-Pin LCCC Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 84073012C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hex D-Type Flip-Flop |
| 84073012X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hex D-Type Flip-Flop |
發布緊急采購，3分鐘左右您將得到回復。